Search:

Type: Posts; User: MartinsX

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    76

    Requested/specified boost pressure looks a bit...

    Requested/specified boost pressure looks a bit too high for me. Any chiptuning/ECU SW modifications done before? EGR removed, maybe? I'd reflash ECU with known good stock SW or swap it with known...
  2. Wiring info: - luggage compartment light (W3)...

    Wiring info:
    - luggage compartment light (W3) supply is separate output from BCM, T52a/3, red/blue wire. No additional load allowed to that output, I think.
    - constant voltage supply for interior...
  3. Anyway not completely clear where OP connected...

    Anyway not completely clear where OP connected the additional light. If OP could make a picture from original WD and draw by hand the extra connections?
  4. Replies
    10
    Views
    211

    Get the WD, check the "holly trinity" first -...

    Get the WD, check the "holly trinity" first - power, ground and data at ABS module connector.
  5. Replies
    39
    Views
    806

    First try to remove O2 sensor and clean it. No...

    First try to remove O2 sensor and clean it. No sharp tools and chemical cleaners allowed! Use soft brush and compressed air.
  6. Replies
    18
    Views
    498

    This product...

    This product helps not in all but a lot of cases ;) It works perfectly where DPF is mounted vertical, horizontal installations sometimes requires two attempts=two cans.
  7. Replies
    27
    Views
    595

    Nothing suspicious. Probably car was used as Taxi...

    Nothing suspicious. Probably car was used as Taxi before and it is speed pulse interface for taximeter installation.
    http://www.canm8.com/can-bus-interfaces/all-interfaces/canm8-pulse.html
  8. Replies
    4
    Views
    213

    Too much fault codes to be caused by faulty G70...

    Too much fault codes to be caused by faulty G70 ... I'd look for hole/source of unmetered air in intake/vacuum/PCV/EVAP systems
  9. Replies
    10
    Views
    183

    I'd like to have 038-906-016-BRS label in German,...

    I'd like to have 038-906-016-BRS label in German, too.
    P.S. Maybe its not a bad idea to include all existing label files in standard English version? If there is no English translation, then include...
  10. Replies
    27
    Views
    595

    But it (0x36) is online for VCDS, only GW...

    But it (0x36) is online for VCDS, only GW complains it is offline... CAN wires interchanged? I mean not H/L but module now is by some reason connected to powertrain or infotainment CAN instead of...
  11. Replies
    27
    Views
    595

    What kind of device was connected to CAN under...

    What kind of device was connected to CAN under seat? Post a photo, if possible. Does the 131660/U0208 00 keep coming back if deleted several times?
  12. Replies
    8
    Views
    225

    Hi! I"d start with basic mechanics. Let's get...

    Hi!
    I"d start with basic mechanics. Let's get more info for beginning. How the chain jumped? Why? Was it broken or only jumped for some teeth? How match? What else parts were damaged/are replaced?...
  13. Thread: VW cc 2013

    by MartinsX
    Replies
    5
    Views
    131

    Check for measurement of steering angle when...

    Check for measurement of steering angle when wheels are positioned straight. Should be around 0 degrees. If it shows + or - 360 or 720 degrees, try to remove it and turn to 0 position. If it does not...
  14. Replies
    2
    Views
    198

    I'd start with deeper investigation what caused...

    I'd start with deeper investigation what caused missfire codes for all bank 2 cylinders. Intake air or vacuum or pcv leak, maybe? Chain between camshafts or adjuster?
    New spark plugs if previous...
  15. Thread: VW cc 2013

    by MartinsX
    Replies
    5
    Views
    131

    Are any repairs done on steering rack/column or...

    Are any repairs done on steering rack/column or connected parts just before fault appeared?
  16. Replies
    7
    Views
    179

    Don't advertise You are a pirate. A lot of people...

    Don't advertise You are a pirate. A lot of people use pirated copies of elsa, but it's illegal... If You had legal elsa on the same computer with legal ODIS, clicking on link would open the...
  17. Use RTFB and Your brain ;) Even if there is no...

    Use RTFB and Your brain ;)
    Even if there is no ECT sensor temperature/resistance chart in repair manual for Your engine, take any older VAG repair manual. ECT sensor temperature/resistance chart is...
  18. If I remember correct, BKS has so called "fast...

    If I remember correct, BKS has so called "fast glow" plugs. They are controlled from their own control module, only first second they get full 12V, then power is reduced by switching to PWM signal....
  19. Replies
    16
    Views
    378

    Use 1J0907375AC if You want to order new unit...

    Use 1J0907375AC if You want to order new unit (electronic box only, something around 1k eur... :D )
    Use 1J0907379AA/1J0907379AG if looking for used unit - this partnumbers are stamped on electronic...
  20. Replies
    7
    Views
    179

    I'd start with monitoring pressure, with VCDS and...

    I'd start with monitoring pressure, with VCDS and mechanical pressure gauge simultaneously. If measurements confirms faulty sensor, I'd try to disassemble module and try to flush out crystallized...
  21. Replies
    16
    Views
    378

    It's better to take one of those ways to get the...

    It's better to take one of those ways to get the correct partnumber:
    -ask official dealer,
    -ask someone who has bought PL24 subscription,
    -buy Your own PL24 subscription (if You are repairing VAG...
  22. Replies
    7
    Views
    179

    1 Fault Found: 11393 - Reductant Pressure...

    1 Fault Found:

    11393 - Reductant Pressure Sensor Circuit
    P204B 00 [232] - Implausible Signal
    MIL ON - Intermittent - Confirmed - Tested Since Memory Clear
    Freeze Frame:
    Fault Status: 00000001...
  23. Replies
    16
    Views
    378

    Do You have an old original ABS module or at...

    Do You have an old original ABS module or at least correct partnumber?
  24. 0x25 not reached may be just a VCDS or computer...

    0x25 not reached may be just a VCDS or computer glitch during autoscan in progress, as other modules don't complain about missing data exchange with immo (I got some modules missing time by time if...
  25. I'm not sure there is any way to cheat glow time...

    I'm not sure there is any way to cheat glow time with VCDS, but You can try to cheat ECT sensor measurement by adding additional wires, manual switch and fixed or variable resistor ;)
    I did this a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4