Search:

Type: Posts; User: downtime

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    88
    Views
    10,220

    Yihaa, now it communicates. Hard reset was...

    Yihaa, now it communicates. Hard reset was needed, meaning battery disconnection. So there must be some kind of address register on the gateway and it did not update that when the CAN bus changed...
  2. Replies
    88
    Views
    10,220

    I did not touch the "original" wiring. I first...

    I did not touch the "original" wiring. I first connected the wires to A pillar connection point, I then extended the wiring and went to gateway connection point. In both cases the result was the...
  3. Replies
    88
    Views
    10,220

    Hmm.... Now this is getting interesting. I...

    Hmm.... Now this is getting interesting. I swapped the CAN wires to DRIVE CAN and I even did it directly to gateway instead of using the A pillar connection point. However, now the suspension control...
  4. Replies
    88
    Views
    10,220

    Yes, Drive CAN is where it’s supposed to go. I...

    Yes, Drive CAN is where it’s supposed to go. I knew that but I didn’t double check the wire colors :)

    And no menu yet, let’s see after the unit is parameterized and calibrated.
  5. Replies
    88
    Views
    10,220

    Aalraity then, installation completed. But stupid...

    Aalraity then, installation completed. But stupid me, attached the unit to the wrong CAN bus. This was the only thing I did NOT check and double check. I trusted the coloring on the Chinese wiring...
  6. Replies
    5
    Views
    111

    ^ That error I’ve seen when the ACC view is...

    ^ That error I’ve seen when the ACC view is obstructed. Means there’s dirt or something blocking ACC view.
  7. Replies
    4
    Views
    114

    Try to recode the headlight range control unit...

    Try to recode the headlight range control unit with the same coding.

    But, I’m pretty sure the problem is with wiring now. Check that. The power module is not even recognized and that should work...
  8. Replies
    88
    Views
    10,220

    Yes I have drive mode select. According to...

    Yes I have drive mode select. According to various websites it does not need FeC. Coding part is to be seen. There are few modules where you need to code the DCC but like you wrote there’s no...
  9. Replies
    4
    Views
    114

    I would say incorrect power module for the...

    I would say incorrect power module for the headlights your friend has installed.

    AFS lights have two modules, ballast and "power module" which controls the AFS functionality. Ballast has no...
  10. Replies
    5
    Views
    111

    Can you get your car autoscanned with a newer HEX...

    Can you get your car autoscanned with a newer HEX CAN v2 cable? It would show the extended info for the error. Might give some hints why the radar is disconnected. That disconnect message is a...
  11. Replies
    88
    Views
    10,220

    First drive to office this morning and I can give...

    First drive to office this morning and I can give my initial thoughts even only rears have been changed.

    Compared to stock R-Line struts, the DCC ones seem to be a bit softer at their default...
  12. Replies
    5
    Views
    111

    The radar is still the main detector for cars,...

    The radar is still the main detector for cars, the camera is just helping in it. So if there's no car image in front the radar has not detected it.

    And the radar does not pick up cars that have...
  13. Replies
    88
    Views
    10,220

    Just couldn’t resist ��

    Just couldn’t resist ��
  14. Replies
    88
    Views
    10,220

    50% of the job done. Rear struts installed and...

    50% of the job done. Rear struts installed and cabled. Also DCC module and rear acceleration sensor installed as well.
    Shitty job :)

    Took four hours but I did install sound absorbers to rear...
  15. ^ And the BCM is still an IF in this case. ...

    ^ And the BCM is still an IF in this case.

    That age Tiguan has most of the parts and is similar in many ways that Golf Plus. I had Golf Plus previously and I did a bixenon retrofit to that. Now I...
  16. I think your BCM is not compatible as it looks...

    I think your BCM is not compatible as it looks like it’s medium and you need high.

    Second as the lights are AFS lights, you need the module so that the lights work correctly.
  17. Looks good! Good to hear that now everything...

    Looks good! Good to hear that now everything works as it should.
  18. Replies
    88
    Views
    10,220

    I agree :) the prices here are total overkill.

    I agree :) the prices here are total overkill.
  19. Replies
    88
    Views
    10,220

    I have as well and I still didn’t want to bother...

    I have as well and I still didn’t want to bother with this. And maybe it’s cheaper to get the parts from Italy but for example the big DCC connector alone was almost 50€ here. The height sensor...
  20. Replies
    88
    Views
    10,220

    All the parts acquired. Now just waiting for a...

    All the parts acquired. Now just waiting for a bit warmer weather and some time.

    Managed to get the parts from exactly same car as mine so no need to change springs etc. Just out with the old, in...
  21. Replies
    30
    Views
    8,982

    But you cannot add the SWaP codes/license...

    But you cannot add the SWaP codes/license yourself. You need factory connection for those.
  22. Replies
    30
    Views
    8,982

    I’m guessing Diskoboy is mixing pr code input and...

    I’m guessing Diskoboy is mixing pr code input and SWaP codes.

    You can input the pr codes to gateway with the other tool but that does not enable the product.
  23. Replies
    15
    Views
    393

    Why only partial autoscan?

    Why only partial autoscan?
  24. Replies
    72
    Views
    69,370

    ”Cluster adapter” works wonders :) like this for...

    ”Cluster adapter” works wonders :) like this for example : https://a.aliexpress.com/3EvwO9Ao
  25. Replies
    72
    Views
    69,370

    Yes you can, and for that reason missing it from...

    Yes you can, and for that reason missing it from the instrument cluster is just a minor thing :)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4