Search:

Type: Posts; User: morski

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Common fault on the 4G platform for the rear hvac...

    Common fault on the 4G platform for the rear hvac motor gears to get stripped. Pull the rear vent out and have a look at the gears to check if they are all still intact.
  2. Check near the battery. Not 100% sure where it is...

    Check near the battery. Not 100% sure where it is on the Q7 but a5,a6,a4's etc are all near the battery. There are/should be some fuses by the battery terminal check them as well. Also have you used...
  3. Recheck the fuses, check your manual for location...

    Recheck the fuses, check your manual for location and numbers. All the faults appear to be from no power to the modules
  4. True dat 1 meant say some who can recode used...

    True dat 1 meant say some who can recode used keys.
  5. Lots of other modules will be VIN attached, eg...

    Lots of other modules will be VIN attached, eg gateway, engine ecu, clocks etc. Too many ecus in the toe-rag iirc
    I would suggest you would be better off keeping the original ecus and getting a set...
  6. here you go... https://imgur.com/eR4qnNw.jpg

    here you go...
    https://imgur.com/eR4qnNw.jpg
  7. Back of the engine bay on the firewall; passenger...

    Back of the engine bay on the firewall; passenger side. Should have a tag attached to it.
  8. Yes exactly but i didnt want to say that about...

    Yes exactly but i didnt want to say that about the little connector plug as dealing with HV systems one never knows how a certain individual might approach these systems. Ive see them with the fuse...
  9. No; basic settings is not the same as shutting...

    No; basic settings is not the same as shutting down/reactivating the hybrid battery system. Its a strict procedure in ODIS that you have to follow in order to reactivate the battery system. Ive...
  10. Ghost immobiliser by any chance?

    Ghost immobiliser by any chance?
  11. What caused the wires to melt in the first place?...

    What caused the wires to melt in the first place? Definitely looks like a wiring issue where there could be more damaged wiring further up/down in the loom. I would suggest getting hold of a engine...
  12. 1st thing is you need to fully charge the...

    1st thing is you need to fully charge the battery! Everything is pointing to a very low voltage on the battery. Dont even bother running diagnostic scans when you have a low battery or at least use ...
  13. Lesson learnt.. And always do an autoscan and...

    Lesson learnt.. And always do an autoscan and save save save!!
  14. The car has obviously been in a collision so you...

    The car has obviously been in a collision so you need to get the other faults cleared as well; mainly the steering angle sensor. Get that calibrated. Easy enough to do!
    What module are you in when...
  15. Have you never scanned his car before? No saved...

    Have you never scanned his car before? No saved logs etc?
  16. My question is: but why? Why not get the correct...

    My question is: but why? Why not get the correct steering for your car in the first place?
  17. Thread: VCDS HEX V2

    by morski
    Replies
    4
    Views
    203

    ok so ive got my hands on it and requested the...

    ok so ive got my hands on it and requested the change of ownership details for the cable online. Got the email back about the re-registration fee.
    Uwe; can you do this for me or do i leave it...
  18. Thread: VCDS HEX V2

    by morski
    Replies
    4
    Views
    203

    Thanks Uwe, Hopefully i'll go and get my hands on...

    Thanks Uwe, Hopefully i'll go and get my hands on it in the next few days
  19. Thread: VCDS HEX V2

    by morski
    Replies
    4
    Views
    203

    VCDS HEX V2

    Hi
    ive already got a Hex CAN cable and am a verified user on here, so my question is if i was to buy a used HEX V2 unlimited vin version from a friend will i still be able to post scans, get help on...
  20. Disconnect the original flexray that comes form...

    Disconnect the original flexray that comes form the abs module and connect it directly to the j533 diagnostic interface under the back seat. Some modules run the flexray to the sensor unit 3B and...
  21. Yes it is but seeing as you have a comms error on...

    Yes it is but seeing as you have a comms error on the flexray i would see what happens if its connected to it directly
  22. try connecting the flexray cable (2 core)...

    try connecting the flexray cable (2 core) directly to the sensor electronics (3B) under the centre console at the rear. Seems to a communication error that i can think of. Failing that replace the...
  23. Thread: Audi a6 2012

    by morski
    Replies
    5
    Views
    246

    The yellow wires are the audi repair wires so it...

    The yellow wires are the audi repair wires so it probably been repaired in the past due to coolant ingress. Your current abs unit has superceeded to newer parts numbers which will work but watch for...
  24. Replies
    55
    Views
    2,538

    Yes i have some access to the official system. PM...

    Yes i have some access to the official system. PM me your email address so ic an send screen shots of your cars details over.
  25. Replies
    27
    Views
    1,320

    And it will kick in as soon as that module is...

    And it will kick in as soon as that module is plugged in. Just assume the module is 50/50 -legit/dodgy and it needs Audis online system to verify/confirm that
Results 1 to 25 of 68
Page 1 of 3 1 2 3