Search:

Type: Posts; User: dieseldub

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Such a load of bollocks. "More people drove...

    Such a load of bollocks.

    "More people drove diesel cars, therefore more CO2 output."

    Sure, burning any fuel makes CO2. But the main reason diesels are popular in Europe is because they're extra...
  2. Judging by the VIN, you have a late production...

    Judging by the VIN, you have a late production 2006 (as in when this car was produced, the gas engines were already transitioned to being 2007 model year production... kind of a long story, but VW...
  3. Replies
    25
    Views
    882

    Strange that your autoscan shows no codes in the...

    Strange that your autoscan shows no codes in the engine computer despite the obvious out of range fuel trim you have going on.

    O2 sensor lean code the only fault it sets?

    Does it ever set a...
  4. Uwe's suggestion on measuring mV drop across...

    Uwe's suggestion on measuring mV drop across fuses is absolutely the best and fastest way to track down what system a draw is coming from.

    Also, leave the driver door open, but trip the latch. The...
  5. Replies
    4
    Views
    176

    The reason you're not seeing fuses for only the...

    The reason you're not seeing fuses for only the mirror adjustment is because they aren't directly fused. On power window mk4s, everything passes through the door control module. The door control...
  6. Just because one individual on their team...

    Just because one individual on their team couldn't figure out a rare, oddball issue doesn't mean all their suggestions are trash...

    Are they all spot on the money the first time? No. But I've...
  7. Depends on what's failed. I've fixed a few that...

    Depends on what's failed. I've fixed a few that did need a new microswitch for the latch open/close recognition because the plunger flat gets worn by the rotary piece.

    I've also had them where the...
  8. VW techline (back when I worked at a dealer) told...

    VW techline (back when I worked at a dealer) told me that little tid bit about cam sync angle or cam phase position (they word it differently in different vehicles).

    Basically, that measured value...
  9. No coding is required. The lock/latch module...

    No coding is required. The lock/latch module electrically is nothing more than a bunch of switches, most all on the same circuit board, and an electric motor. It is not diagnostic capable, it's just...
  10. Strange, the key in the door lock should...

    Strange, the key in the door lock should mechanically unlock, as well as send the disarm signal on the comfort data bus. And since you stated the windows roll down when the key is turned to unlock,...
  11. Replies
    17
    Views
    784

    Mk4 era, they all definitely have a separate VSS....

    Mk4 era, they all definitely have a separate VSS. Even the DSG Beetle (also with BEW engine). Though what's interesting there is the Mech unit generates the VSS and sends it to the cluster, cluster...
  12. Replies
    17
    Views
    784

    Also, for what it's worth, the Mk4 generation...

    Also, for what it's worth, the Mk4 generation cars are the last ones to have VSS as its own separate set of wires going to modules individually.

    Starting with the Mk5s, the ABS module generates...
  13. Replies
    17
    Views
    784

    I got wiring diagrams from erwin.vw.com, though...

    I got wiring diagrams from erwin.vw.com, though like I said, for this specific model, the VSS wiring is not 100% accurate in a single diagram. The 09A diagram shows what wire goes between TCM and ECU...
  14. The screen blowing out on the bridge is a stupid...

    The screen blowing out on the bridge is a stupid common failure. And if that check valve and spring have come out, definitely need a whole new bridge.

    Audi says it's actually OK, if not...
  15. Replies
    17
    Views
    784

    As I scrolled down further in the log, I noticed...

    As I scrolled down further in the log, I noticed you actually had some MVB 006 info. Now, it doesn't tell me if the Set and Res switches are working, but it is at least recognizing that the system is...
  16. Replies
    17
    Views
    784

    I've become quite familiar with the daisy-chain...

    I've become quite familiar with the daisy-chain VSS wiring in BEW automatics from doing a few manual swaps with them.

    The BEW in the Golf/Jetta that comes bolted to the 09A transmission are pretty...
  17. Replies
    3
    Views
    264

    A way you can put VCDS to use to check for chain...

    A way you can put VCDS to use to check for chain stretch before it causes an issue, login to the engine computer. Go to Meas. Values.

    Enter number 93, GO! Make note of the number in field 3. If...
  18. From the New Beetle repair info I have, here's...

    From the New Beetle repair info I have, here's the coding table from the early Mk20 systems:

    Code Table
    Code number Engine code Variant
    03504 AGU ABS
    13504 AGU ABS/EDL
    03504 AEG ABS
    13504 AEG...
  19. Not a bad idea. I think some of the aftermarket...

    Not a bad idea. I think some of the aftermarket replacement pumps also don't have the sheath but do have a provision for the actuator plug and a resistor built in so it doesn't set a code.

    For...
  20. It's strange that when you unplug it, it doesn't...

    It's strange that when you unplug it, it doesn't overheat. But does when it's plugged in. Usually when these fail and cause an overheat, it's physically jammed covering the impeller, and unplugging...
  21. Thread: Boost issue

    by dieseldub
    Replies
    10
    Views
    349

    Well, did you try any of the suggestions I had...

    Well, did you try any of the suggestions I had above to look for while performing the basic setting test for the boost control circuit?

    Watch the actuator and see if it moves all the way to its...
  22. Replies
    20
    Views
    251

    I'm not as familiar with the UDS modules to know...

    I'm not as familiar with the UDS modules to know exactly how it is worded, but in older KWP modules there was a measured value block that shows you the 1s and 0s of cruise control and pedal switch...
  23. First off, you need to physically unplug and...

    First off, you need to physically unplug and remove the old transmission computer. Then you can also code the CAN gateway to no longer look for the transmission computer. Current coding being 00007...
  24. Replies
    9
    Views
    235

    Does your engine have an actual physical...

    Does your engine have an actual physical dipstick? If not, I would leave the level sensor coding alone so you can still at least get an idea of what the oil level is. Fairly certain coding out that...
  25. Replies
    4
    Views
    195

    I would also not take all the information in the...

    I would also not take all the information in the myturbodiesel.net link as gospel, since the V10 operates very differently from the commonrails.

    The V10 being a PD does not have adequate control...
Results 1 to 25 of 54
Page 1 of 3 1 2 3