Search:

Type: Posts; User: golfi_vend

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Is wiring correct? You may wanna look at...

    Is wiring correct?

    You may wanna look at Measuring Values in Module 16 if SWCM sees signal from MFSW-module. And then MVB in 09 module if they are transmitted from SWCM(16) module.
  2. Your old module had G85 sensor built in. Your...

    Your old module had G85 sensor built in. Your current CD doesn't.

    Luckily You have a gen3 zf steering rack with built in sensor. Check the adaptions there and turn on steering rack internal sensor.
  3. This car is a mess. I might be able to check...

    This car is a mess.

    I might be able to check VIN if this car has a dvd changer, but right now it's missing communication. It either doesn't have it or has MOST- loop installed.

    Also Battery...
  4. Without modding ECU software by tuner - NO

    Without modding ECU software by tuner - NO
  5. Replies
    12
    Views
    949

    I was dealing with this quite recently. Coding...

    I was dealing with this quite recently. Coding goes as follow:

    00?xxxx: Auxiliary Functions
    0 = Start-Stop not active/installed
    2 = Start-Stop is active/installed

    00x?xxx: Remote Control
    0 =...
  6. Replies
    7
    Views
    210

    Pressure profile is loaded to module via...

    Pressure profile is loaded to module via parameters. Can't be done with vcds.

    You might be able to chabge individual value in adaption.
  7. Replies
    5
    Views
    3,247

    Hello I'm in the same situation with this Audi...

    Hello

    I'm in the same situation with this Audi S7.
    I've retrofitted IsoFix fitting to Passenger Seat. Replaced GloveBox harness and added cutoff switch. I'm experiencing same fault codes.

    So...
  8. Thread: Golf 7 Navi

    by golfi_vend
    Replies
    3
    Views
    174

    I think OP tries to install MIB1-PRO display to...

    I think OP tries to install MIB1-PRO display to MIB1-Media.

    This is not possible due to different resolution....
  9. AFAIK You can't. With new MFK 3.0 it is FEC.

    AFAIK You can't. With new MFK 3.0 it is FEC.
  10. Where is autoscan? Halogen Headlights?

    Where is autoscan?

    Halogen Headlights?
  11. Replies
    10
    Views
    434

    You May wannaa try: 088A440008

    You May wannaa try: 088A440008
  12. Replies
    6
    Views
    167

    Unlock the steering, clear faults and cut wire...

    Unlock the steering, clear faults and cut wire for escl so it will never bothers again.
  13. Replies
    10
    Views
    434

    Please be noted that label file may not be loaded...

    Please be noted that label file may not be loaded correctly due to being Audi SW nr, though HW is identical.
    There was talk about this on some other thread, but I don't have access to redir file to...
  14. Replies
    10
    Views
    434

    Yes Highline SWCM that actually supports MFSW....

    Yes Highline SWCM that actually supports MFSW.
    Direct replacement would be 5k0-953-569-bd. You don't want to go lower because some options may not be supported like Limiter.
  15. Replies
    4
    Views
    282

    Have You looked into ADP of 5F and 57? There

    Have You looked into ADP of 5F and 57?
    There
  16. It could be programmable, but that would mean it...

    It could be programmable, but that would mean it is dataset with ODIS.
    Alos P/N AC is dropped and was only available suggestion in the ETKA catalogue for Chineese Audi A4L.
  17. What You're after is k2xxx train file for mib2 to...

    What You're after is k2xxx train file for mib2 to update from k1xxx to k2xx. This will fail though because train check.

    SD updates are either ordered or downloaded via sd-maker, but that requires...
  18. Replies
    6
    Views
    345

    You most likely need to clear them using OBD2...

    You most likely need to clear them using OBD2 mode.
  19. Replies
    8
    Views
    348

    It should be the preGP unit without smooth glass....

    It should be the preGP unit without smooth glass. - Picture would be handy here.
    But yes You can swap it for GP unit 8inch glass with buttons. Resolution is the same and it will start working. It...
  20. ESP is OK and compatible. Fuel chart may be...

    ESP is OK and compatible.
    Fuel chart may be tweaked in eeprom.
  21. How was the coding lost with just engine swap? ...

    How was the coding lost with just engine swap?

    Been here?
    https://forums.ross-tech.com/showthread.php?20619-MK60EC1-ABS-FAQ&highlight=mk60ec1

    But idk..... try: ...
  22. Which means that Service Table is not correct....

    Which means that Service Table is not correct.
    Seen it many times after resetting it with ODIS.
  23. Replies
    9
    Views
    350

    Even if not same lenght or same module...or...

    Even if not same lenght or same module...or coding will help to code Even newer module....
  24. Replies
    2
    Views
    170

    There is a page for this in my wiki. :) ...

    There is a page for this in my wiki. :)

    https://i.postimg.cc/Z0hbmGQ2/Screenshot-20200127-183045.jpg
  25. Lucky You, who You get it replaced Under...

    Lucky You, who You get it replaced Under warranty.
    There is TPI that states that injectors are not included in "Trust building measures".
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4