Search:

Type: Posts; User: Mika_M

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: NOx capacity

    by Mika_M
    Replies
    4
    Views
    82

    SSP 424 states that there is indeed a level...

    SSP 424 states that there is indeed a level sensor G697 in AdBlue tank. But you are right, it is not a float type sensor. There are only four electrodes of different length, one of which is the...
  2. Went to dealer today to get few things fixed (air...

    Went to dealer today to get few things fixed (air quality sensor, blind spot detection dropping when engaging reverse etc). They told me not to worry about the wheel temp sensor error. It exists in...
  3. Skoda Kodiaq steering wheel temp sensor fault

    291104 - Temperature Sensor for Heated Steering Wheel
    B1455 01 [008] - Electrical Failure
    Intermittent - Confirmed - Tested Since Memory Clear

    Any information or clues about...
  4. Replies
    0
    Views
    174

    2017 Skoda Kodiaq 2.0TDI DFHA

    Tuesday,20,August,2019,20:08:15:26429
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows XP x86
    VCDS Version: 19.6.0.2 HEX-V2 CB: 0.4505.4
    Data version: 20190529 DS308.0
    www.Ross-Tech.com...
  5. N422 and N82 seem to reference the same valve:...

    N422 and N82 seem to reference the same valve: "Certain vehicles without an auxiliary heater (optional equipment) were fitted with vacuum-actuated coolant shut-off valves from the start of production...
  6. I would guess the answer is no and no. ...

    I would guess the answer is no and no.

    Although, you CAN enable the mirror reverse function, but it will probably not work as it should since you do not have the electric seats with memory. I...
  7. After battery replacement, did you also code the...

    After battery replacement, did you also code the replacement in CAN gateway...? If not, your car still thinks it has the old battery and that may (or may not) cause many weird things.
    ...
  8. Well, should have guessed that, thanks for the...

    Well, should have guessed that, thanks for the clarification!
  9. Well, the main problem of misfiring was solved...

    Well, the main problem of misfiring was solved quickly. A little "inspection hole" to the exhaust system and... It works. Car can be driven again. Catalytic converter is pretty much toasted and...
  10. 2002 Audi A4 3.0 V6 ASN misfiring, fuel trim stays zero?

    I was helping out to find out why this poor V6 ASN engine is misfiring BADLY on bank 2. With engine idling, cylinders 4-5-6 generate misfirings faster than I can read them out. Bank 1 cylinders 1-2-3...
  11. Replies
    9
    Views
    468

    I had these exact symptoms in my A3 8V. Reason...

    I had these exact symptoms in my A3 8V. Reason was, ignition lock was somehow physically stuck in such a way that it did not register key being taken out. Car thinks the key is still inserted and...
  12. Thread: Audi a3 8v TPMS

    by Mika_M
    Replies
    2
    Views
    263

    If we are talking about indirect TPMS and "not...

    If we are talking about indirect TPMS and "not able to view when i am driving" means that the option is greyed out when car is moving, then it's working as intended.

    You can only enter TPMS menu...
  13. Replies
    5
    Views
    477

    Maybe this explains:...

    Maybe this explains: https://forums.ross-tech.com/showthread.php?1905-UDS-Vs-non-UDS

    In short, you can find the data in Advanced measuring values.
  14. Replies
    7
    Views
    389

    I don't think that rear WIPER settings will help...

    I don't think that rear WIPER settings will help to resolve new WINDOW motors? :p

    I would go searching in modules 42 & 52, which both have a submodule for rear doors. Maybe VCDS will show some...
  15. Replies
    1
    Views
    303

    You could try this: Module 09 Security access...

    You could try this:

    Module 09
    Security access 20113
    Adaptation channel 34

    - subtract 4 from the value = SS off by default

    - add 32 to the value = SS button memory, so if you turn it off,...
  16. Replies
    10
    Views
    582

    Would not take this for granted. Although a...

    Would not take this for granted. Although a different engine, but in my A3 8V 1.8TFSI CJSB I had a leaking thermostat. Could not get engine to normal operating temperature no matter what, but ECU was...
  17. Replies
    21
    Views
    1,469

    Don't know about this specific mod, but some...

    Don't know about this specific mod, but some changes to MQB BCM lighting functions need a complete BCM shutdown before they come to life. Means that car has to sit ignition off and doors locked for...
  18. Replies
    9
    Views
    424

    Equal under-inflation detection is based on tire...

    Equal under-inflation detection is based on tire resonance frequency. This resonance frequency can be estimated with signal processing from wheel speed sensors. I do not pretend to understand this...
  19. Always, ALWAYS make the Auto-scan before anything...

    Always, ALWAYS make the Auto-scan before anything else...

    There is a place, where VCDS automatically logs every change you make, maybe from there you can dig your original coding etc? Check this:...
  20. Replies
    2
    Views
    346

    It's kind of annoying to try measure exact...

    It's kind of annoying to try measure exact charging voltage, since it is constantly adjusted and thanks to recuperation, car doesn't even try to fully charge the battery.

    I'm using Binary-AGM on...
  21. Thanks, that's a good tip! Didn't go in to...

    Thanks, that's a good tip! Didn't go in to digging coding, when I did the auto-scan. But will definitely change this to pre-heat engine also. :thumbs:
  22. Much appreciated! :thumbs:

    Much appreciated! :thumbs:
  23. Yes, I get that double-check would be necessary,...

    Yes, I get that double-check would be necessary, that's why I was hoping that golfi_vend would have enough spare time to maybe help me out... :)

    As I was checking from one online source, I found...
  24. Any news about this...? I think that we would...

    Any news about this...?

    I think that we would need receiver 3Q0 963 513, remote 3G0 963 511, wiring harness for receiver (for LIN, +12VDC, ground) and antenna for receiver. Am I forgetting...
  25. Yes, so it seems. Found this as a reference scan:...

    Yes, so it seems. Found this as a reference scan: https://forums.ross-tech.com/showthread.php?14188-VW-Transporter-T6-Address-18-Aux-Heat-Adaptation-FAIL

    Address 18: Aux. Heat (J364) ...
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4