Search:

Type: Posts; User: RyMar

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Also think pump or ECU? Donít have a decade box....

    Also think pump or ECU? Donít have a decade box. Not allowed to buy any type of equipment from VW/Audi in South Africa. Will need to source equipment overseas and import. No function on VCDS to...
  2. As per Elsa diagram wiring checked. Fault code...

    As per Elsa diagram wiring checked. Fault code cannot be erased, comes back after start up. Will connect battery charger and rerun scan and post.
  3. Audi Q5 2.0 Tdi, reductant pump 1, open circiut

    Checked relavent wiring up to control unit and found to be OK. No Is it possible for this pump to fail at this kilometer reading?


    Wednesday,11,September,2019,11:49:13:48706
    VCDS -- Windows...
  4. Replies
    3
    Views
    127

    Try do read temperatues on engine & gearbox with...

    Try do read temperatues on engine & gearbox with vehicle idling and aircon off until the rad fan switches on/off? Then switch the aircon on and monitor the temps again? Is there any difference? Also...
  5. Replies
    4
    Views
    240

    Make sure all tyres are pumped to spec. Swith the...

    Make sure all tyres are pumped to spec. Swith the switch in the cubby on and test drive. Should reset then.
  6. Replies
    5
    Views
    265

    Advanced id`s are the same. Code rejected,...

    Advanced id`s are the same.
    Code rejected, Error31, Request of range for coding supplied.
  7. Were you able to check on MVB`s for ash load?...

    Were you able to check on MVB`s for ash load?
    Maybe if the ash load is too high one can investigate leaking injectors?
    No black puffs of smoke from the exhaust?
    Engine not noisy/clattering at...
  8. Replies
    5
    Views
    265

    Jetta 6 ABS coding lost?

    Jetta was towed in and an engine swop was done.
    For some reason the ABS coding is zero and we would like to do basic settings etc but when logged in it throws an error.
    Any suggestions please?...
  9. Replies
    8
    Views
    501

    Scan: Wanted to adjust TPMS shown in instrument...

    Scan: Wanted to adjust TPMS shown in instrument cluster/radio but no functions available.


    Thursday,22,November,2018,15:15:53:48706
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7...
  10. Audi A4 ABS warning lights comes on even when standing still & idling

    2x Extra fault codes also on cluster: Headlight range contr defective, Start system fault funtion unavailable. And these contr modules are not picked up on the scan?
    Software fault?
    ABS wiring was...
  11. Replies
    8
    Views
    501

    I far as my knowledge is, In South Africa Touareq...

    I far as my knowledge is, In South Africa Touareq TPMS work through ABS contr module and there is no way one can alter/program different pressures.
  12. Toureg air suspension not working with no warning lights

    No warning lights on instrument cluster, suspension contr knob not working and sport/normal/comfort button not working. Ride height normal and no sagging suspension.

    Any ideas please?

    ...
  13. Replies
    3
    Views
    243

    Oil Service intervals every 15000km or yearly....

    Oil Service intervals every 15000km or yearly. Service intervals 30 000km or yearly. (Fixed).
    Does not want to download! 09 Central Electrics it downloads (140kb data) for example, not for 17 (1kb...
  14. Replies
    3
    Views
    243

    6R Polo Cross service ESI not reset

    Managed to reset oil service but no functions available for inspection service reset.


    Wednesday,05,December,2018,07:36:15:48706
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x64...
  15. There is not a aftermarket `tracking` type system...

    There is not a aftermarket `tracking` type system fitted? In the past a found a couple of these systems will come alive at some stage and the current draw will increase. It usually happens when the...
  16. My understanding if the battery is not coded you...

    My understanding if the battery is not coded you will loose battery life? Not battery drain.
  17. Do you have clamp tester or multimeter to test...

    Do you have clamp tester or multimeter to test for current draw at battery? Close and lock all doors (alarm) and wait at least 2min for all systems to go into `sleep` mode and check draw.
  18. 10896 does not work. I tried 20103 again and...

    10896 does not work. I tried 20103 again and accepted. In adaptations I changed the setting from 255 to 260 and it was accepted and the new no was 4? I did all the channels and checked the cluster....
  19. 20103 gives access. Then when you try do...

    20103 gives access. Then when you try do adatation downwards is states request out of range.
  20. Replies
    49
    Views
    3,951

    This Gti is fitted with 4 wire after cat sensor?...

    This Gti is fitted with 4 wire after cat sensor? The voltage then should run around 0.45V. If the ECU does not see this it will think something is wrong with the cat and will make the ECU send rich...
  21. Tried to but cannot get it to adjust! Not from...

    Tried to but cannot get it to adjust! Not from the steering controls or on the infotainment.
    User manual has settings that this Touareg does not have.
  22. Is there a security access code? Does not want to...

    Is there a security access code? Does not want to adapt directly.


    Friday,23,November,2018,08:49:36:48706
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x64
    VCDS Version: 18.9.0.2...
  23. I saw those channels and the values for front and...

    I saw those channels and the values for front and back fully/partially loaded was at 255.
    I will try and reduce and see where the pressures on the cluster goes.
  24. Touareg coding tyre pressure monitoring (2014 7P)

    This vehicle for partial load front is set at 2.3 bar and rear at 2,5bar.
    Is there a way to reset all ex at2.2 bar?


    Thursday,22,November,2018,15:15:53:48706
    VCDS -- Windows Based VAG/VAS...
  25. Replies
    2
    Views
    299

    Took a photo of the pistons with bore scope....

    Took a photo of the pistons with bore scope. Found no 1 piston crown pit marks on the top of the crown and starting to burn away.
Results 1 to 25 of 168
Page 1 of 7 1 2 3 4