Search:

Type: Posts; User: darkchina811

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    96
    Views
    10,579

    @downtime can you also describe how to perform...

    @downtime

    can you also describe how to perform basic settings? I know the car has to be lifted from ground with all 4 wheels hanging. then? what entry you selected in what menu? was VCDS enough or...
  2. Replies
    96
    Views
    10,579

    I enabled that very bit but didn't get the menu,...

    I enabled that very bit but didn't get the menu, but my shocks were still disconnected so no basic settings yet.
  3. Replies
    17
    Views
    260

    my stock value for byte 4 was FF, when I...

    my stock value for byte 4 was FF, when I installed a non-OEM DSP/AMP with high level inputs I changed the byte to AA to get rid of the error in the 5F about speakers. I don't remember how I...
  4. http://goo.gl/D37qgp This is Xagico PDF. check...

    http://goo.gl/D37qgp

    This is Xagico PDF. check page 229.
  5. you're Spanish... check your fellow Xagico PDF...

    you're Spanish... check your fellow Xagico PDF for traffic sign recognition instructions, what you're looking for is one adaptation in 5F.

    I have limited internet access so cannot research more.
  6. if that guy has fogs then yes, BCM is good for...

    if that guy has fogs then yes, BCM is good for fogs. he also published adaptation maps so compare his to yours with WinMerge.

    I think fog lights in german are called Nebellichts.
  7. if you have navigation, then the "fusion" setting...

    if you have navigation, then the "fusion" setting is not working, most probably something has to be changed in module 5F.

    if you don't have navigation, it cannot be fixed. same on my Golf. it...
  8. no problem, but since my BCM is also the...

    no problem, but since my BCM is also the old-style coding, I never researched much on the new generation. I am sure somebody will chime in soon.

    anyways, did you replace it already? that was fast...
  9. Replies
    17
    Views
    260

    I might be missing something, and fairly big....

    I might be missing something, and fairly big. it's four channels, 1,1,2,2,3,3,4,4. if you go behind the units, speaker outputs are 8 pins, so again, four channels.
  10. Replies
    17
    Views
    260

    if the 5F has four outputs, and the speakers are...

    if the 5F has four outputs, and the speakers are 8, then each WF is paralleled to its TW... WD doesn't lie.
  11. Replies
    96
    Views
    10,579

    glad you are making progress. if you use...

    glad you are making progress. if you use experimental coding you will find a bit in the gateway that has DCC in the description, it's in german so no clue on what it does. I enabled it and the...
  12. Replies
    17
    Views
    260

    ditto, but a wrong balance/fader setting would...

    ditto, but a wrong balance/fader setting would not kill the woofers. WF and TW are brutally paralleled with just a crappy capacitor filtering low end from tweeters.

    check the bass and treble...
  13. Replies
    2
    Views
    190

    post an autoscan so we see what ABS module you...

    post an autoscan so we see what ABS module you have.

    if it's like the MQB ABS, you just send a switched +12V to a certain pin on the ABS module.
  14. Replies
    17
    Views
    260

    if you have the cable then post an autoscan ;) ...

    if you have the cable then post an autoscan ;)

    you either have a wiring problem or your woofers are blown...
  15. Replies
    96
    Views
    10,579

    CAN addressing memory? not that I know of, but...

    CAN addressing memory? not that I know of, but maybe try leaving the car battery disconnected for a while...

    sure you didn't swap L to H and viceversa? or that the twisted pair got somehow...
  16. coding for what? coding follows the car's...

    coding for what? coding follows the car's features and will vary.

    ask a more specific question or look back into this section of the forum and you might get lucky.

    welcome to the forum :P
  17. worked for me, and the fader is still there, even...

    worked for me, and the fader is still there, even if I couldn't care less. rear speakers are disconnected.
  18. Replies
    96
    Views
    10,579

    well the chinese harness can lie but I am sure...

    well the chinese harness can lie but I am sure the WDs you have from erwin don't :P DCC goes to the powertrain bus if I am not mistaken.

    so, did the menu just magically appear?
  19. Replies
    96
    Views
    10,579

    my question was incorrect because on MQB you...

    my question was incorrect because on MQB you can't have DCC without the Drive Mode Selection. I should have said I hope the FeC for Driving Mode only is not different from the FeC for Driving Mode +...
  20. Replies
    96
    Views
    10,579

    do you have Driving Mode Selection? I ask because...

    do you have Driving Mode Selection? I ask because I am curious to know how you'll enable DCC into the menu, as module 14 has no coding. in theory it should appear after you code the other modules for...
  21. Replies
    96
    Views
    10,579

    yeah, like I ever believed you were really gonna...

    yeah, like I ever believed you were really gonna wait until the summer :D
  22. Replies
    3
    Views
    127

    for A3 8V, the side sensor brackets are not...

    for A3 8V, the side sensor brackets are not available as spare part, they come molded with a new bumper for PLA. I have a fried who installed the sensors with Golf brackets I suggested, and it works...
  23. of course I upgraded my BCM, the MID one I had...

    of course I upgraded my BCM, the MID one I had from stock did not support heated seats. if you search the forum there was another guy retrofitting heated seats and I walked him through the BCM swap...
  24. BCM needs to be replaced with 5Q0 937 084 DD,...

    BCM needs to be replaced with 5Q0 937 084 DD, this would also facilitate other retrofits. honestly I am not completely sure, as there is no way to tell from the part number, but the higher BCM for...
  25. I believe the culprit here is to change byte 4...

    I believe the culprit here is to change byte 4 from FF to AA ;)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4