Search:

Type: Posts; User: siLc

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. 0AM198140L is the clutch kit which has currently...

    0AM198140L is the clutch kit which has currently lasted me close to 120000km. By now it has been superseded to 0AM198142AA, though the LUK and Sachs part numbers will still be the same. When changing...
  2. Replies
    7
    Views
    216

    The part number 6R0907357 of module 55 tells us...

    The part number 6R0907357 of module 55 tells us this CC has the "low" xenon lights with additional H7 cornering bulbs inside. One could guess these should be set up as "static cornering lights"...
  3. 02811 - Control Module for Electronic Steering...

    02811 - Control Module for Electronic Steering Column Lock (J764)
    014 - Defective
    Freeze Frame:
    Fault Status: 01101110
    Fault...
  4. Replies
    5
    Views
    235

    On the Audi A6 C5 there is no module 09 and 46....

    On the Audi A6 C5 there is no module 09 and 46. What are you trying to achieve?
  5. Thread: Today I F'd up

    by siLc
    Replies
    3
    Views
    208

    Buy an hours access on ErWin, get the WD-s for...

    Buy an hours access on ErWin, get the WD-s for your car, list out the dead fuses and see what they have in common.
  6. According to the drive2 article, those clutch...

    According to the drive2 article, those clutch parameters aren't good.

    Where are you seeing this clutch date info? My vehicle is manufactured september 2011 and gearbox code is NAU. Yours is most...
  7. Replies
    3
    Views
    160

    Thats a well-known fault of the A6 C7. And you...

    Thats a well-known fault of the A6 C7. And you don't have to paint the new sharkfin to your vehicle's color - the painted cap from the old sharkfin can be transferred to the new.
  8. Replies
    9
    Views
    259

    I vaguely remember the retrofit from anything...

    I vaguely remember the retrofit from anything else to a 090 BCM needed wiring work - running additional battery powers to the BCM, which it appears to be currently missing.

    There should be threads...
  9. Replies
    63
    Views
    4,596

    If the measuring blocks are correct (you could...

    If the measuring blocks are correct (you could try searching again if anything with a similar description exists), I would try unplugging a sensor and seeing if an appropriate DTC is logged and if...
  10. Replies
    9
    Views
    259

    Dealers usually insist on installing a component...

    Dealers usually insist on installing a component which is appropriate to the particular vehicle as per VIN and which the factory diagnostic tool will adapt to the vehicle without fuss.

    What BCM...
  11. Replies
    3
    Views
    165

    This is only the installation list, please post a...

    This is only the installation list, please post a full autoscan. Into 6th gear at approximately 55-60km/h is normal and doing basic settings probably won't improve it. Does it shift harshly from 1->2...
  12. No problem! A horse trailer puller? I've only...

    No problem!

    A horse trailer puller? I've only pulled light trailers (750kg fully laden) with my 2011 Passat B7 CNG and it felt like torturing the DSG clutches while maneuvering :) My ex-Swedish...
  13. Is this info for the 6-speed DQ250 DSG? Don't...

    Is this info for the 6-speed DQ250 DSG? Don't think this applies to the 7-speed DQ200...
  14. Well, there were some improvements to the CDGA...

    Well, there were some improvements to the CDGA engine on the B7 but if the swapped B6 engine itself is running fine, why bother for now? I hope you at least changed the timing chain on the replaced...
  15. Lot of things to address, lets get going... ...

    Lot of things to address, lets get going...

    First, please post all autoscan data using the English language version of VCDS. You can install it besides your Swedish version. Most people able to...
  16. Replies
    17
    Views
    536

    If I remember correctly, your retrofits have been...

    If I remember correctly, your retrofits have been quite OEM but this 3x power strip in the passenger footwell doesn't look very OEM to be honest :/
  17. Replies
    63
    Views
    4,596

    You can check the measurement blocks for the side...

    You can check the measurement blocks for the side sensors. Do they indicate plausible distance values?
  18. Replies
    51
    Views
    957

    In zero or auto position with xenons off - LED...

    In zero or auto position with xenons off - LED DRL should be full bright.
    In auto or lights on position with xenons on - LED DRL should be less bright.
    In parking light position, LED DRL should be...
  19. Replies
    7
    Views
    279

    Vehicle is FWD and has self-parking and it only...

    Vehicle is FWD and has self-parking and it only takes one type of rear ABS sensors (left) - WHT 003 859A (supersedes to WHT 003 859B). Did you try these?
  20. Address 4F: Centr. Electr. II (J520) ...

    Address 4F: Centr. Electr. II (J520) Labels:. 1K0-907-532.clb
    Part No SW: 7N0 907 532 HW: 7N0 907 530 AN
    Component: EZE_2 H56 1663
    Revision: H56 Serial number:...
  21. Replies
    51
    Views
    957

    I'm not very familiar with DCC but chances are if...

    I'm not very familiar with DCC but chances are if DCC is made happy again by fixing this issue, the xenon leveling might be one step closer to working.


    01769 - Sensor for Vehicle Leveling; Front...
  22. There is no energy management and hence, no...

    There is no energy management and hence, no battery coding, on a Passat B6.
  23. Replies
    7
    Views
    14,337

    https://www.drive2.com/l/538296979654967321/ ...

    https://www.drive2.com/l/538296979654967321/

    Have a look. I once went over this using Google Translate and there should be something pertaining "tolerance" ranges which can be read from the TCM...
  24. There's reason to believe that there is some CAN...

    There's reason to believe that there is some CAN communications trouble with the TCM. If able and feasible, you could try to obtain a test mechatronic unit - you can plug it in without installing it...
  25. If the test unit was operational otherwise, you...

    If the test unit was operational otherwise, you can try swapping (desolder-solder) the displays from your old unit to the test unit.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4