Search:

Type: Posts; User: b00nSai

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    4,971

    All right, then I will contact a distributor here...

    All right, then I will contact a distributor here in Germany and get a new one. I consider it "learning the expensive way" ;P
    Thanks for the support!
  2. Replies
    19
    Views
    4,971

    I've now resoldered another plug that doesn't...

    I've now resoldered another plug that doesn't have that short between CanL and VG. I matched the pinout from the old plug-board to the new one, so there should be no issues. If I connect it with the...
  3. Replies
    19
    Views
    4,971

    Hi Uwe, I have resoldered the chip and...

    Hi Uwe,

    I have resoldered the chip and desoldered the plug board. I still have that contact from CAN-Low to vehicle ground. I don't know what to think of this. I cant spot any components on that...
  4. Replies
    19
    Views
    4,971

    I've desoldered the MCP2551 and a 120Ohm resistor...

    I've desoldered the MCP2551 and a 120Ohm resistor between CANH and CANL on the right side. I still have a short to ground for CANL. I'll resolder the chip but I don't know where this short is coming...
  5. Replies
    19
    Views
    4,971

    Judging from the copper color that appears after...

    Judging from the copper color that appears after scratching, I would say this is a valid path. I need to get myself a magnification glass, as I don't have one here. I've ordered the MCP2551 but it...
  6. Replies
    19
    Views
    4,971

    The MCP2551 was indeed hiding under the voltage...

    The MCP2551 was indeed hiding under the voltage regulator, but no sight of any resistors in the 60Ohm range.

    https://i.ibb.co/jG7st1W/20181125-191358.jpg
  7. Replies
    19
    Views
    4,971

    Here is the board from both sides. ...

    Here is the board from both sides.
    https://i.ibb.co/6tTJt51/20181125-155959.jpg
    https://i.ibb.co/mBH21Gs/20181125-160013.jpg

    Julian
  8. Replies
    19
    Views
    4,971

    I can try to locate it on the PCB and replace it...

    I can try to locate it on the PCB and replace it with another one, IF I can find another one online.
    So I would conclude that I spent 270 € for a faulty cable and I should never again buy special...
  9. Replies
    19
    Views
    4,971

    It seems like I have a short from Can-Low to...

    It seems like I have a short from Can-Low to Vehicle-Ground. Unfortunately, I can't spot an obvious reason on first sight. Do you have any hints?

    Julian
  10. Replies
    19
    Views
    4,971

    I was not sure how much of the PCB I can show in...

    I was not sure how much of the PCB I can show in public, so I framed just the pinheaders. There is "HEX-PRO_4" etched on the PCB. Is it normal the PCB is fixed by hot glue?
    I measured the following...
  11. Replies
    19
    Views
    4,971

    Yes that could be correct, as I bought it second...

    Yes that could be correct, as I bought it second hand. Which would explain why somebody wanted to get rid of it. :/
  12. Replies
    19
    Views
    4,971

    Can: not ready in can Car

    Hi Forum,

    I have issues with a HEX-USB+CAN cable. In the settings I get the error that the can is not ready, although a friend with a diffrent cable is able to do so. ...
Results 1 to 12 of 12