Search:

Type: Posts; User: tomk_22

Search: Search took 0.01 seconds.

  1. Does this give you ideas as to what the problem...

    Does this give you ideas as to what the problem is? Or why it is now giving a 008820 (too lean) code?
  2. today I retested all sensor heater circuits and...

    today I retested all sensor heater circuits and all seem good. so I then hooked up the scope to the heater signal wire at the ECM and the other channel to the power supply wire to attempt to catch...
  3. thanks for the link on how to insert code. I have...

    thanks for the link on how to insert code. I have been trying to find proper testing procedure in the manual but I cannot seem to find much information on this, especially the specs for these...
  4. Hmmmm... it sounds like you think its possible...

    Hmmmm... it sounds like you think its possible that one of the other sensors could be bad causing this issue with sensor 3. How would i go about testing the other sensors to either verify that they...
  5. the post-cat sensor is the one that i am having...

    the post-cat sensor is the one that i am having trouble with and i have recently replaced it with a brand new one from the dealer that has less than 50 miles on it at this point. i have checked the...
  6. i have tested everything that i can possibly...

    i have tested everything that i can possibly think of and everything appears to check out just fine. are there any VAG scans, or tests that i can run with with a scope box that i could post that...
  7. hi jack, could you please explain to me how to...

    hi jack, could you please explain to me how to properly isolate and test the components?
  8. I guess that im looking for some guidance on how...

    I guess that im looking for some guidance on how to properly do this.
  9. I have back probed harness at ECM and graphed...

    I have back probed harness at ECM and graphed MBV, both readings matched perfectly. The code did set while driving and scope connected but there were never any voltage drop outs during the drive...
  10. sorry again for the long delay in my response....

    sorry again for the long delay in my response. things came up that did not allow me to look work on the car for a while. i load tested all 4 wires with a 55w headlight bulb that i rigged up as a test...
  11. thanks guys, sorry it took so long to repy. i...

    thanks guys, sorry it took so long to repy. i went and bought another OE sensor from the dealer just to verify that it was not a bad sensor. same issues with this one as others. slightly more...
  12. O2 sensor diagnostic help

    i have been having repeated O2 sensor codes 000327 & 000326, all related to B1S3 with a 2010 Beetle 2.5 engine code BPR. I have tried a couple of different sensors that I had laying around and they...
  13. thanks jack for the info regarding the warranty....

    thanks jack for the info regarding the warranty. im pretty confident that my problem is either a wiring or a ECM issue. because the same "intermittent" faults with several different sensors. im now...
  14. the car has a salvage title so im sure the dealer...

    the car has a salvage title so im sure the dealer will use that as an excuse to void the warranty.
  15. here are the diagrams that i am using. its my...

    here are the diagrams that i am using. its my understanding that the warranty on this vehicle is 6 years/72k miles


    http://oi63.tinypic.com/28t9mpu.jpg
    http://oi64.tinypic.com/2958k79.jpg...
  16. i was able to get the beetle specific diagrams,...

    i was able to get the beetle specific diagrams, but as i suspected it is very similar to the jetta one that i had. shows 2 feed wires from fuse #43, that feed all three oxygen sensors and the fuel...
  17. so i have narrowed this down to an intermittent...

    so i have narrowed this down to an intermittent power feed issue. as stated before i have diagrams for a jetta but not a beetle. in the jetta manual is shows that the o2 sensors are fed 12v+ through...
  18. the mode one stuff came up as an excel...

    the mode one stuff came up as an excel spreadsheet and im not sure how to post that.


    Thursday,11,April,2019,08:17:28:11370
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
    VCDS...
  19. sorry for the delayed response guys, it took me a...

    sorry for the delayed response guys, it took me a while to get everything together...the engine code is BPR and here is a complete scan after clearing and no codes present along with the OBD scans...
  20. i have the diagram for a jetta, but it appears to...

    i have the diagram for a jetta, but it appears to be pretty "simple". 1 wire from fuse box and the others go to ecm.
  21. 2010 beetle oxygen sensor faults... please help!!!

    I have A 2010 vw Beetle with 2.5 L engine. I keep getting trouble codes associated with oxygen sensor B1S3. I have replaced the sensor twice and the same codes keep appearing. There are no noticeable...
Results 1 to 21 of 21