Search:

Type: Posts; User: darkchina811

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. of course if you have FAZIT access ;)

    of course if you have FAZIT access ;)
  2. usually we want to upgrade a MID BCM/GW to a HIGH...

    usually we want to upgrade a MID BCM/GW to a HIGH because it will allow several retrofits. but if you upgrade to a different generation (eg the car is 2015 and you install a 2018 module), then there...
  3. since you lost Driving Profiles and bluetooth...

    since you lost Driving Profiles and bluetooth they is a high chance that they messed up the FeC codes. if the car was stock I would go back to dealer and insist to have a SVM SPEC VS ACTUAL performed...
  4. Replies
    22
    Views
    9,358

    rear level sensor is directly connected to module...

    rear level sensor is directly connected to module 14. if you remove the module, the sensor wires need to be extended to the front of the car and connected to module 55/4B (whatever is handling...
  5. you don't have to replace it, you need to have...

    you don't have to replace it, you need to have FeC codes restore into it. there is a special guided function into ODIS for that.
  6. +1, happened to me as well when I replaced the...

    +1, happened to me as well when I replaced the gateway.
  7. and how to enable this for MQB with old style...

    and how to enable this for MQB with old style coding for the BCM?
  8. Replies
    8
    Views
    167

    I didn't know that. I also heard that starting...

    I didn't know that. I also heard that starting from 2020 ODIS won't work with VAS5054A anymore, it will require the "newer" interface.
  9. Replies
    8
    Views
    167

    how so? if I had a geko account, would VCDS be...

    how so? if I had a geko account, would VCDS be able to access it?
  10. Replies
    8
    Views
    167

    you should have an "activation document" which...

    you should have an "activation document" which contains a code for performing the SVM, but it needs to be done with a dealer-level diagnostic cable. VCDS cannot perform SVM.
  11. I am away from my Golf until early december so I...

    I am away from my Golf until early december so I can only report what I remember. car came stock with CarPlay and one USB port, almost certainly 5G0 035 222 E. on the stock HSD connector that goes...
  12. the 46pin connector part number is 8V0 998 623,...

    the 46pin connector part number is 8V0 998 623, and the sealing pin for unpopulated positions will be 5Q0 971 904 (you can also use silicone sealant...).
  13. glad to hear you sorted it out but $400 still...

    glad to hear you sorted it out but $400 still sounds like too much...
  14. yes, the hub ports have to be enabled by...

    yes, the hub ports have to be enabled by adaptations. also, the black hub port is charging only.

    as a side note, I have always found CarPlay to be somewhat picky. it does not work with all iPhone...
  15. find one of those shops where they replace car...

    find one of those shops where they replace car windshields/windows. nowadays they need to be equipped with calibration jigs for the various ADAS. if they're honest they'll charge 100-200.
  16. yes, and I am using option 2, so the displayed...

    yes, and I am using option 2, so the displayed speed limit is often wrong.
  17. Replies
    19
    Views
    9,870

    man, I just reported my experience. the board was...

    man, I just reported my experience. the board was even professionally printed, and on a panel, not on paper. a friend and I spent a good hour in making sure the car was as aligned as possible, with...
  18. Replies
    19
    Views
    9,870

    your calibration target board is NOT in the...

    your calibration target board is NOT in the correct position, period. it may look like it is, but that's the reason why the factory calibration jig has lasers, to align the board within a VERY tight...
  19. first thing to do is always to post an autoscan...

    first thing to do is always to post an autoscan ;)
  20. free hint: before pulling out one entire row, or...

    free hint: before pulling out one entire row, or the whole fusebox, take pictures with your cell phone. been there :P
  21. I have TSR working with a Composition Media, no...

    I have TSR working with a Composition Media, no navigation. it works but it will generate a warning on the cluster, something like "TSR currently restricted". it only happens once per ignition cycle....
  22. buy one hour access on erWin and you'll be able...

    buy one hour access on erWin and you'll be able to print-to-PDF all wiring diagrams related to your VIN.
  23. I told him long ago about ABS sensors :) but he...

    I told him long ago about ABS sensors :) but he never confirmed he looked at them...
  24. you can probably use my ABS also, it's a 46 pins,...

    you can probably use my ABS also, it's a 46 pins, I did all sorts of retrofits and everything works great... but I do have the Electronic Parking Brake, and I don't know if that can be coded out.
  25. ebay object 223487907520

    ebay object 223487907520
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4