Search:

Type: Posts; User: tamorgen

Search: Search took 0.02 seconds.

  1. Replies
    20
    Views
    583

    That would be crazy if it's that simple. I...

    That would be crazy if it's that simple.

    I read something that if one component is wrong on Flexray, the whole line will shut down. This could be what I'm experiencing.
    I should also probably...
  2. Replies
    20
    Views
    583

    Okay, good to know. Just trying to eliminate...

    Okay, good to know. Just trying to eliminate chasing a wild goose.
  3. Replies
    20
    Views
    583

    Okay, here's another question.... I'm assuming...

    Okay, here's another question.... I'm assuming that the modules I'm trying to communicate with may have Component Protection. Would they show up on the scan if the component protection was enabled?
  4. Replies
    20
    Views
    583

    Yeah, trying to do this from my phone. The links...

    Yeah, trying to do this from my phone. The links should now work, but it won’t embed the images. I’ll try and fix when I get home.
  5. Replies
    20
    Views
    583

    So, I was looking in the Green Menu, and I came...

    So, I was looking in the Green Menu, and I came across a portion of the menu where you can set what CANBUS interface a module is on. Is it possible I’m not seeing those modules because of the...
  6. Replies
    20
    Views
    583

    Yeah, I thought about that later. I may have...

    Yeah, I thought about that later. I may have just been tired when I read the fluke.
  7. Replies
    20
    Views
    583

    Well, I went through the wiring at the CAN...

    Well, I went through the wiring at the CAN Gateway, and everything appears to be correct based upon the ELSA wiring diagrams. All the wires are secure in their correct locations. No change. This...
  8. Replies
    20
    Views
    583

    I would tend to agree with that assumption. ...

    I would tend to agree with that assumption.


    I pulled off the front bumper cover, verified that I didn't do something stupid like putting the wrong module on the wrong side. They are correct.
    ...
  9. Replies
    20
    Views
    583

    I wouldn't expect coding to provide a total lack...

    I wouldn't expect coding to provide a total lack of comms either, but you never know. I'll have to check the Installation List. I must have missed 13-Auto Dist. Reg in my comparison. The Touareg...
  10. Replies
    20
    Views
    583

    Uwe I've made significant headway thanks to your...

    Uwe
    I've made significant headway thanks to your 15 TDI Exec reference scan. I'm still not getting communication with 8B ACC2 or 8E Image processor. I'll need to make sure the connections are all...
  11. Replies
    20
    Views
    583

    Thanks Uwe, I'll check all that tonight. On...

    Thanks Uwe, I'll check all that tonight.

    On another note, what's the deal with: [New feature! Extended UDS fault detail is only supported by current gen. interfaces]?

    I know there is a...
  12. Replies
    20
    Views
    583

    Help retrofitting on 2013 Touareg TDI

    Good evening,
    I've been wanting to retrofit several features on my 2013 Touareg TDI Exec. A while ago, I installed the Area View camera, and that went pretty well. The big project I've been...
  13. I broke down and just bought a new clock spring. ...

    I broke down and just bought a new clock spring. Now my G85 sensor is calibrated correctly again, and the ESC error went away. I'm still getting the same "Steering Wheel error, 01044 - Control...
  14. Hey Uwe, I believe I know what the issue is that...

    Hey Uwe, I believe I know what the issue is that I'm getting with the Steering Wheel error, 01044 - Control Module Incorrectly Coded. G85 won't code, but I was troubleshooting with a friend, and we...
  15. The steering wheel stalk needed to be replaced...

    The steering wheel stalk needed to be replaced for the controls for side assist and for ACC when it gets installed. That coding is the original coding.

    I think the error may because the steering...
  16. Okay, my wife came home briefly with the Touareg...

    Okay, my wife came home briefly with the Touareg and I managed to get a scan. I changed the setting in 5F for Lane Change Menu, but it's still not showing up. The change I made last night, which...
  17. Do you happen to know what the coding is just for...

    Do you happen to know what the coding is just for side assist?
  18. It does when you go into the individual...

    It does when you go into the individual components. It may have crapped out on the autoscan on that section.
  19. Well, that's a small step forward. It brought up...

    Well, that's a small step forward. It brought up the Assistants menu on the cluster. Unfortunately, the only system it has, and it's unchecked, is Sign Assist. I'm still unable to clear the error...
  20. Problems coding Steering Wheel - 2013 Touareg

    I'm trying to retrofit Side Assist (blind spot monitoring radars) to my 2013 Touareg. I've got the radars in, wired up, and they are coded into the car. What I'm having problems with is the...
  21. Replies
    5
    Views
    2,612

    Look at this post...

    Look at this post. It can be done, but you will have to calibrate it. Calibration requires a special board, which you have to make yourself, or get from the dealer.
  22. Replies
    10
    Views
    19,346

    cgalford, Did you ever complete this retrofit? ...

    cgalford,
    Did you ever complete this retrofit? I'm in the process of gathering all of the parts. One thing you didn't add, is that if you are retrofitting this to a 2011-2014 Touareg, you need the...
Results 1 to 22 of 22