Search:

Type: Posts; User: DrPeter

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    1
    Views
    90

    Hi there, Sounds like you need to have a look...

    Hi there,

    Sounds like you need to have a look at the Official Factory Repair Information

    drpeter
  2. Replies
    1
    Views
    91

    Hello, 17-Instruments -- Status:...

    Hello,






    17-Instruments -- Status: Cannot be reached 0100
    56-Radio -- Status: Cannot be reached 0100
    5F-Information Electr. -- Status: Cannot be reached 0100
  3. Replies
    5
    Views
    133

    Hello, The fault code [P0556 00] refers to...

    Hello,

    The fault code [P0556 00] refers to the [G294 - brake Booster Pressure Sensor] which is located on the Brake Booster vacuum hose.

    The G294's pressure is in hPa, so a value of 280-300...
  4. Replies
    4
    Views
    149

    Hi, well..... that sounds normal, because in '10...

    Hi, well..... that sounds normal, because in '10 minutes (or more) and you only get about 25 to 30ml'

    Thanks for asking,

    drpeter
  5. Replies
    4
    Views
    149

    Hello, There is a way to test the...

    Hello,



    There is a way to test the N474-Reducing Agent Injector. The steps below should work for this vehicle:
  6. Replies
    6
    Views
    263

    Hello, Based on my research and as far...

    Hello,




    Based on my research and as far as I can tell, when replacing the transmission and/or the J743-Mechatronics controller, there are only two things that need to be done and both can be...
  7. Hello, If the two engine blocks are the same...

    Hello,

    If the two engine blocks are the same (CBEA) then why can you not swap or use the same parts from the original engine?

    Maybe post some photos so we can 'see' what you are looking at....
  8. Thread: Comeback P0333

    by DrPeter
    Replies
    1
    Views
    105

    Hello, We do have a Ross-Tech wiki page for...

    Hello,

    We do have a Ross-Tech wiki page for this fault code, see the link below.

    P0333 - Knock Sensor 2 (G66): Signal too High

    I would like to add, you can have a look at the Measuring...
  9. Replies
    4
    Views
    178

    Hi, Just throwing this out, but it seems that...

    Hi,

    Just throwing this out, but it seems that many dealerships are not willing or able to run the 'SVM / Actual vs. Specified test plans' with used controllers.

    You could go in there and ask...
  10. Replies
    3
    Views
    142

    More and more Maps... Address [6C] ...

    More and more Maps...

    Address [6C]

    blockmap-6C-4M0-980-556-A


    ;SW:4M0-980-556-A HW:4M0-980-556-A --- Back-up Cam.
    ;Component:RVC Compact H12 0250, Coding:0294010102002001400040...
  11. Replies
    3
    Views
    142

    More maps... Address [29] ...

    More maps...



    Address [29]

    adpmap-29-4M0-907-397-AC


    ;SW:4M0-907-397-AC HW:4M0-907-397-C --- Left Light
  12. Replies
    3
    Views
    142

    Maps Address [01] blockmap-01-8W0-906-259-J...

    Maps

    Address [01]

    blockmap-01-8W0-906-259-J


    ;SW:8W0-906-259-J HW:06L-907-425-C --- Engine
    ;Component:2.0l R4 TFSI H15 0002, Coding:0A2500322326010E34280000000000000000000000000000...
  13. Replies
    3
    Views
    142

    2018 Audi A4 - SilverCar Scans and maps

    Hello,

    The following information is from a 2018 A4 SilverCar. For some reason, I was under the impression it was a 2019. Supposedly, Silvercar will be phasing out the Audi A4 models and keeping...
  14. Replies
    2
    Views
    121

    Hello, The transmissions may appear to be the...

    Hello,

    The transmissions may appear to be the same, both are 09G six speed automatic transmission.

    They may bolt up and work fine, however I would be careful. Here is what I found and you can...
  15. Hello, Based on some research, there does...

    Hello,



    Based on some research, there does not appear to be any Security Access code needed for the Adaptation Channel that is used to relearn the ADR(Automatic Distance Regulation) Sensor.
    ...
  16. Replies
    9
    Views
    289

    I do not recall any mention of any calibrations...

    I do not recall any mention of any calibrations of the J428 if the battery was disconnected. I do see the repair manual states the following:



    So I think it is safe to disconnect the battery...
  17. Replies
    9
    Views
    289

    Hello, The fault codes that are present in...

    Hello,

    The fault codes that are present in your Auto-Scan would indicate there is a concern with the J428-Adaptive cruise control unit, it's wiring/connections or it's components. You may want to...
  18. Hello, Use VCDS to go in to the...

    Hello,



    Use VCDS to go in to the [19-Gateway] controller, then use the [Meas.Blocks-08] and have a look at the Group [125 to 129] for the CAN-Data bus Powertrain (Communication).

    Everything...
  19. Hello, I would check the power/fuses,...

    Hello,



    I would check the power/fuses, ground and connections to the J525-Digistal Sound Package control unit before condemning it.

    You maybe able to disconnect the power from it (or the...
  20. Replies
    12
    Views
    419

    On the main page of VCDS, there is an...

    On the main page of VCDS, there is an [Applications] button, and on that screen, there is a [Controller Channels Map] button.

    Press that and a pop-up window appears.
    Single Controller Address...
  21. Replies
    12
    Views
    419

    Hello, Yep, been looking into this :) ...

    Hello,



    Yep, been looking into this :)

    Your coding in the [09-Cent. Elect.] seems plausible, I see two examples of this exact coding in very similar vehicles.

    Are you suspecting the...
  22. Hello, The ECM may not run the Basic...

    Hello,



    The ECM may not run the Basic Settings when there are fault codes. You can run the Output Tests to hear/feel if the N205-Camshaft Adjustment Valve clicks on/off, do this with the key...
  23. Big Bears don't cry.... Big Bears don't cry....

    Hi there....

    Went to the woods and found "dabear" looking sad, so I tried to ask what was wrong... :p


    https://youtu.be/t_8cJjrdTs4

    drpeter
  24. Replies
    2
    Views
    90

    Hello, Have you seen this Ross-Tech wiki...

    Hello,



    Have you seen this Ross-Tech wiki page? Basic Setting for Hydraulic Unit Intake Valves / Hydraulic Unit Disconnecting Valves


    We also have a video that will help too....
  25. Replies
    7
    Views
    195

    - Sometime a 'running' compression test can help...

    - Sometime a 'running' compression test can help you 'see' if there are any valve train concerns.

    If you have never performed this test, it is easy to do.
    - Remove a spark plug (one cylinder at a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4