Search:

Type: Posts; User: Jack@European_Parts

Page 1 of 20 1 2 3 4

Search: Search took 0.53 seconds.

  1. Well here is the first bank! FDIC announces...

    Well here is the first bank!
    FDIC announces first bank failure of coronavirus crisis

    https://www.marketwatch.com/amp/story/guid/A949EFE8-86C5-45EA-AE09-7B4F20E2428B
  2. Nobody cares act? ...

    Nobody cares act?

    https://www.cnbc.com/2020/04/03/delays-in-sba-loans-for-independent-contractors-self-employed-workers.html

    Coronavirus loan program delayed for independent contractors and...
  3. My point was that an un-configured factory tester...

    My point was that an un-configured factory tester cripples functions and is only for "looking" & not "telling", further being less perfect or inferior than VCDS!

    ...
  4. You would be right to observe the RTFB and get...

    You would be right to observe the RTFB and get verified for forum & so we can help you more with a complete auto-scan.... :p

    JPPSG
    ...
  5. An original factory tester from day one if...

    An original factory tester from day one if reading the RTFB & if it was not configured; stated that a tester would not permit coding or a login and or adaption procedure.
  6. Replies
    29
    Views
    513

    Well no login attempt....... Sigh

    Well no login attempt....... Sigh
  7. Did you overlay or check wiring for open for feed...

    Did you overlay or check wiring for open for feed consumer BUS and current tracks back to ECU yet for respective components?

    Fuses!
  8. Dam! /\ :cry:

    Dam! /\
    :cry:
  9. Well being stealthy implies hiding. :D Me...

    Well being stealthy implies hiding. :D
    Me personally I think fair is fair, if you are in there, you should be with full disclosure, especially if you expect a warranty if messing with stuff.
    Why...
  10. That means your tester is not setup properly yet...

    That means your tester is not setup properly yet because you didn't RTFB.

    I believe the USB is all that will need to be hooked up to the computer to configure VCDS but it would be best to have...
  11. Did you disconnect battery and run a jumper to do...

    Did you disconnect battery and run a jumper to do capacitor discharge & for 5 minutes and then remove jumper and reconnect battery and restart the cars systems like a computer being rebooted?

    Is...
  12. Replies
    4
    Views
    119

    https://i.imgur.com/eTu9lha.png Voltages are...

    https://i.imgur.com/eTu9lha.png


    Voltages are low and high in time stamps too be sure not under or over voltage now and that current is available no just voltage at respective module, in addition...
  13. Battery Jesus default reboot yet? How about...

    Battery Jesus default reboot yet?

    How about re-coding the Sloppy Kessy with different WSC and same data?

    I see there was an update to the Kessy too but you seem to be at it, maybe have...
  14. Replies
    29
    Views
    513

    Is it not better to know or verify, versus...

    Is it not better to know or verify, versus speculate?
  15. Did you unplug everything with exception of TV...

    Did you unplug everything with exception of TV under hood and attempt a TV adaption yet to isolate everything in engine bay?

    If the aforementioned permits the TV to adapt, could you not plug in...
  16. How about from the OBD2 mode 0x33 in VCDS main...

    How about from the OBD2 mode 0x33 in VCDS main screen?
    0x33-03 then 04 multiple times?
    Function 03 read DTC's
    Function 04 clear DTC's
  17. Replies
    13
    Views
    337

    Did you read about default of control units &...

    Did you read about default of control units & "battery Jesus" reboots?
    Did you power down reboot entire car?
    Did you recode the ABS module with same coding and different WSC & tester number yet...
  18. Many forget to check. Did you know I have yet...

    Many forget to check.

    Did you know I have yet to see a controller that needed it for the minor tweak often permitted without security access?
  19. You need to fix faults first..... Fuses and...

    You need to fix faults first.....
    Fuses and grounds Okay?
    Most likely wiring, bad TV or ECU.....un-modify and install stock ECU to verify TV adapts.
  20. Did you know some controllers support a bump up...

    Did you know some controllers support a bump up or down 30-50 rpm in adaption and require no login to do it?
  21. Yeah well how would I know this is a different...

    Yeah well how would I know this is a different thread and no scan posted in it to ID it?

    I have to pay so why not you but you could call dealer no?

    Maybe not duplicate but indeed incomplete.
  22. "Looks good from my house" sometimes is the best...

    "Looks good from my house" sometimes is the best policy OP.
  23. Fuse, Ignition switch or terminal relay? Car is...

    Fuse, Ignition switch or terminal relay?
    Car is CAN high/low and K line is there but highly unlikely your issue.
  24. You certainly are aggressive to get a solution &...

    You certainly are aggressive to get a solution & with this issue in 3 threads started and one merged/locked already? :p


    Did you try to re-code the 0x53 original module and with a manual terminal...
  25. Replies
    29
    Views
    513

    Certainly no sign of a login default attempt &...

    Certainly no sign of a login default attempt & code erase either and is standard operation procedure for a dealer doing a FaZit session, no?

    I saw the scan which is why I stated the aforementioned...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4