Search:

Type: Posts; User: Jef

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. I would be shocked if any dealer had that part...

    I would be shocked if any dealer had that part number sitting around... heck, shocked if a warehouse had one ready to go. My guess is it will be made to order... a virgin J527 box will be flashed...
  2. Hardware part number is the physical box. The...

    Hardware part number is the physical box. The Software part number has to do with the firmware put into said box. When you scan any given control module with VCDS, on the "Open Controller" screen,...
  3. In before Jack points out there is a firmware...

    In before Jack points out there is a firmware update for this ECM, looks like you should be at firmware level 1649, not 0655. I think it would be safe to assume firmware updates are tied to...
  4. Replies
    8
    Views
    197

    Can't help but notice this: Is there ANY...

    Can't help but notice this:


    Is there ANY hardware in this car that was NOT factory installed? Maybe some parts swapping or something?
  5. Replies
    4
    Views
    71

    Start the engine, let idle for 10 seconds, shut...

    Start the engine, let idle for 10 seconds, shut engine off. Turn ignition on, do not start engine. Connect to the ECM and do the Output Test... one of those test will be for the relay (J299) that...
  6. Every car sold since maybe 2008 or 2009 should...

    Every car sold since maybe 2008 or 2009 should have at least 1 paperless report (like an auto-scan, but with a lot of trash tossed in) from when the PDI was done. There should be a paperless report...
  7. Then I think you still have a wrong J527 part...

    Then I think you still have a wrong J527 part number

    5980040000 coding breaks down as follows:

    Byte 0 : 59

    Bit 0 = G85
    Bit 3 = Auto trans but no kessy
    Bit 4 = rear wiper
    Bit 6 = trip...
  8. Replies
    4
    Views
    156

    Info on where to purchase wiring diagram info...

    Info on where to purchase wiring diagram info here:

    http://wiki.ross-tech.com/wiki/index.php/Official_Factory_Repair_Information
  9. Replies
    3
    Views
    106

    While I don't think this will be a coding issue,...

    While I don't think this will be a coding issue, lets be sure it is actually back to the original coding value...

    Codinglog.CSV

    And of course any time you run Auto-Scan, VCDS automagically...
  10. Coding looks good to me for both TCM and J527. ...

    Coding looks good to me for both TCM and J527. This seems to be a bit of a "base" model vehicle.

    Using PL24 to look up the J527 part number... it doesn't give a part number, it states to use a...
  11. Replies
    4
    Views
    156

    We all know what I'm going to post.... :rolleyes:...

    We all know what I'm going to post.... :rolleyes:

    For any given control module to communicate, it must have THE HOLY TRINITY!
    https://i.imgur.com/G8YGwbm.jpg

    Looks like SA20 and SB31 are the...
  12. Thread: AC fault codes

    by Jef
    Replies
    7
    Views
    166

    The G65 is the High Pressure Sensor. It has 3...

    The G65 is the High Pressure Sensor. It has 3 wires:


    /1 = br, ground
    /2 = li/ge, to HVAC (J255) T20c/2
    /3 = bl/sw from fuse SC13 (5A)


    Unplug the sensor, make sure the electrical...
  13. Replies
    1
    Views
    55

    Vehicle support, moved to proper location so more...

    Vehicle support, moved to proper location so more eyes can get on it. Please provide a FULL Auto-Scan!

    If the top is fully closed and locked up, or fully open and secured, what do all the...
  14. Thread: AC fault codes

    by Jef
    Replies
    7
    Views
    166

    Please post the FULL Auto-Scan!...

    Please post the FULL Auto-Scan!
  15. Replies
    1
    Views
    86

    Thank you for posting a full Auto-Scan! :thumbs:...

    Thank you for posting a full Auto-Scan! :thumbs:

    As per the VIN, ABS coding looks like it would be 0013581. EPB soft coding would be 0000011.


    However, the 02433 fault code in the EPB module...
  16. Replies
    12
    Views
    391

    So you tried the Basic Setting steps?

    So you tried the Basic Setting steps?
  17. Replies
    3
    Views
    187

    Connect to the Instrument Cluster, go into...

    Connect to the Instrument Cluster, go into Adaptation and read channel 60. What is the stored value?
  18. Replies
    18
    Views
    5,509

    ST?ID=92867 No comm with car. Using a...

    ST?ID=92867

    No comm with car. Using a HEX-USB+CAN (HEX+CAN), port test comes up as not plugged up to car. Is the LED on the HEX+CAN powered up? Nope. Plug up to any other car, does the LED...
  19. Replies
    18
    Views
    5,509

    ST?ID=92832 2008 R32 ...

    ST?ID=92832

    2008 R32

    P0491 001169 VCDS-EN-190211 Secondary Air Injection System: Bank 1: Insufficient Flow
    P0492 001170 VCDS-EN-190211 Secondary Air Injection System: Bank 2: Insufficient Flow...
  20. Replies
    25
    Views
    769

    I would avoid using a scan tool to bleed or flush...

    I would avoid using a scan tool to bleed or flush the brakes. Pressure bleeding is the way to go. Early on at my VW dealer days, I was involved several times with trying to use the scan tool to...
  21. Replies
    5
    Views
    246

    ABS coding will be 0013755. EPB module coding is...

    ABS coding will be 0013755.
    EPB module coding is 0000013

    Go to this wiki page:
    http://wiki.ross-tech.com/wiki/index.php/VW_Passat_(3C)_Parking_Brake

    Work your way through the items listed...
  22. Thread: Linde forklift

    by Jef
    Replies
    4
    Views
    226

    MVB group 241 should be: field 1 = Particle...

    MVB group 241 should be:


    field 1 = Particle Filter,Oil Ash Volume,Range: -380...+380 ml
    field 2 = Soot Load(g),Calculated
    field 3 = Soot Load(g),Measured
  23. Going to hold judgement on anything until we know...

    Going to hold judgement on anything until we know compression numbers and the results of coil/plug juggling.

    A lot of "Intermittent" codes, do they come back if cleared out? Note the one in the...
  24. Thread: Linde forklift

    by Jef
    Replies
    4
    Views
    226

    DPF regen? Hmmmmm.... You can try Security Access...

    DPF regen? Hmmmmm.... You can try Security Access 27971 to enable Basic Settings and then Basic Settings group number 226 for regeneration while standing. This is an educated guess.

    I'd be a bit...
  25. Before you clear fault codes, what is the data in...

    Before you clear fault codes, what is the data in 01-08-032 and 11-08-032?

    To expand on what Jack asked about the MAF, please read over this article about Fuel Trim Info. Really take in the part...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4