Search:

Type: Posts; User: Robski

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    8
    Views
    166

    I don't have/use one, I went by PL24 & like I...

    I don't have/use one, I went by PL24 & like I said the 1K0 907 379 AN wasn't listed in the remarks section as an older replaceable module.
  2. Replies
    8
    Views
    166

    so the module fitted now is acceptable ? the part...

    so the module fitted now is acceptable ? the part number isn't listed at all under the VIN ??

    EDIT: this one's fixed now with an accepted string of :

    113B00D092400FF881402EA901B00823000
    ...
  3. Replies
    20
    Views
    644

    reply #11 Check advanced ID of the...

    reply #11

    Check advanced ID of the immobiliser and engine for identical VINs as well please
  4. Replies
    8
    Views
    166

    thanks again, same story mate ! going by PL24...

    thanks again, same story mate !

    going by PL24 the module part number should be : 1K0 907 375 AN , so I'm going to have to see if the previous place have still got the old module to check/confirm ?
  5. Replies
    8
    Views
    166

    hello, thanks for the quick response, the coding...

    hello, thanks for the quick response, the coding was accepted but now throws 01044- control module incorrectly coded DTC !
  6. Replies
    8
    Views
    166

    ABS coding help please ? (MK60EC1)

    Can anyone assist in coding help after used module fitted to vehicle (not by me) please ?


    Saturday,31,August,2019,17:25:26:47217
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86...
  7. Replies
    5
    Views
    211

    no.................

    no.................
  8. Replies
    3
    Views
    165

    does the module see the input from the button...

    does the module see the input from the button when pressed every time thereafter ? if so try recoding the module with the same string ........

    EDIT: I'm assuming you've done some testing ?
  9. Replies
    15
    Views
    894

    I'll let them off, they have adjusted the rear...

    I'll let them off, they have adjusted the rear according to that report. The front is set on the outer limit & rear spot on (total toe) according to my info per PR code on the report, 0deg10' +/- 10'...
  10. Replies
    15
    Views
    894

    post a picture of it .............

    post a picture of it .............
  11. Replies
    15
    Views
    894

    my bet is they haven't touched the rear & haven't...

    my bet is they haven't touched the rear & haven't tracked the front to follow the thrust angle !
  12. Short Term Fuel Trim & Long Term...................

    Short Term Fuel Trim & Long Term................ BUT on a diesel :facepalm: :rolleyes:

    In short pal don't waste your time !
  13. Replies
    11
    Views
    3,603

    like I said mate it was a while ago & I tried...

    like I said mate it was a while ago & I tried just in the cluster, I then got a WD with the intent of fixing & saw another module involved which I found the coding in.
    Sorry for the bum steer, I...
  14. Replies
    11
    Views
    3,603

    I said 'iirc' , pull up a WD & see which other...

    I said 'iirc' , pull up a WD & see which other modules are involved in the brake pad warning circuit, I did this & was quite a while ago now .
  15. Replies
    11
    Views
    3,603

    IIRC it's in 0X09 as well.

    IIRC it's in 0X09 as well.
  16. Replies
    14
    Views
    6,007

    the numbers in the quote are as per VIN & PR code.

    the numbers in the quote are as per VIN & PR code.
  17. Replies
    14
    Views
    6,007

    Headlight: 8lG (PR code)Gas discharge headlamp...

    Headlight: 8lG (PR code)Gas discharge headlamp (D1/D3 system)

    5G2 941 039 left
    5G2 941 040 right


    8K0 941 597 E is the ballast which is correct.
    3D0 941 329 E must be the range control...
  18. Replies
    2
    Views
    4,393

    so if I'm reading correctly here a few parts have...

    so if I'm reading correctly here a few parts have been hung but no actual testing ?

    Time to RTFB & test & prove or pass the job on to someone that can, you owe the customer this at least.
  19. Replies
    16
    Views
    5,663

    KW = kurbelwellengraden (spelling(?)) =...

    KW = kurbelwellengraden (spelling(?)) = crankshaft degrees
  20. basic settings 011

    basic settings 011
  21. Thread: G450 Adaptation

    by Robski
    Replies
    21
    Views
    13,361

    suffix B is correct.

    suffix B is correct.
  22. Thread: ODIS for SKC

    by Robski
    Replies
    7
    Views
    2,307

    no, I saw it too somewhere & remember it being in...

    no, I saw it too somewhere & remember it being in a session log ??
  23. thank you I shall do !

    thank you I shall do !
  24. so a SW update screwed the interface ? This is...

    so a SW update screwed the interface ?

    This is a reason I'm still on vers 15 & ignoring update prompts.
    Am i safe to update ? (Hex+CAN+USB)
  25. Replies
    30
    Views
    9,652

    RPM will be limited without a VSS, carry out a...

    RPM will be limited without a VSS, carry out a boost test in BS.
Results 1 to 25 of 97
Page 1 of 4 1 2 3 4