Search:

Type: Posts; User: HMC

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    260

    Hi AshB Was it a brand new injector? What does...

    Hi AshB
    Was it a brand new injector? What does the garage that fitted it have to say?
    Regards HMC
  2. Replies
    2
    Views
    131

    Hi Artic Fox, You don't say what year your...

    Hi Artic Fox,
    You don't say what year your Ducati is, but I would think it has the old Fiat 3 pin connector for diagnostics, so you would need an adaptor to 16 pin. Your best bet is the Android...
  3. Hi jgc1980, Have you checked the battery leads...

    Hi jgc1980,
    Have you checked the battery leads for volt drop under load, particularly the earth? Connect a DVOM between the battery earth and an earth on the engine, crank the engine and tell us...
  4. Replies
    3
    Views
    151

    Thanks Jack, Jeff and Uwe for fixing the code...

    Thanks Jack, Jeff and Uwe for fixing the code tags (I forgot exactly how to do it, nor could I find the instructions),
    Looks like I will have to give this one a miss, it's from another garage...
  5. Replies
    3
    Views
    151

    2013 Q7 J519 question

    Hi Everyone,
    I hope a simple question, I need to replace the J519 Onboard Supply Control Unit because of a supply loss to the R/H headlamp on T10a/4. What I need to know is if Component Protection...
  6. Replies
    4
    Views
    197

    Hi Adecood, As Uwe say's you would only be able...

    Hi Adecood,
    As Uwe say's you would only be able to get OBD related data. You will not be able to access ABS, Instruments, CAN etc. I have used VCDS on a Triumph to look at EOBD data and clear DTC's....
  7. Hi David, As Uwe said, without a DTC it is hard...

    Hi David,
    As Uwe said, without a DTC it is hard to focus on any area, so you need to log whatever data you can, to diagnose what is happening. In addition you may need to manually check things with...
  8. Replies
    38
    Views
    1,259

    Yes, a compression test would be my starting...

    Yes, a compression test would be my starting point, followed by checking for an induction leak.
    Regards HMC
  9. Hi AlixKaur, "when the main beam is on, the...

    Hi AlixKaur,
    "when the main beam is on, the dipped beam turns off", that might be sensible to stop the headlamp and bulb holder melting.
    Regards HMC
  10. Replies
    4
    Views
    484

    Hi nightcasters, The question I have is, were...

    Hi nightcasters,
    The question I have is, were the previous repairs not replacements? if the servo hose was just repaired at the point of the crack, then the answer is yes the part should be...
  11. Hi Karl, I would think a vehicle reboot is worth...

    Hi Karl,
    I would think a vehicle reboot is worth a try, disconnect the battery for 30 mins and then do an autoscan and post it here, then clear all the codes and see what happens.
    Regards HMC
  12. Replies
    10
    Views
    355

    HI Ossy, The car is not legal for road use in...

    HI Ossy,
    The car is not legal for road use in the UK and will fail an MOT. I hope you got it cheap.
    Regards HMC
  13. "Any Ideas ??" Yes. paste a full autoscan!...

    "Any Ideas ??" Yes. paste a full autoscan!
    Regards HMC
  14. Replies
    6
    Views
    254

    Hi bn1990, Are you ignoring " 7690 - Oxygen...

    Hi bn1990,
    Are you ignoring " 7690 - Oxygen (Lambda) Sensor B2 S1 P2240 00 [039] - Pump Current Open Circuit" for any particular reason? Have you checked any live data for the O2 sensors?
    Regards...
  15. " Camshaft should be around 400 at idle ". Or to...

    " Camshaft should be around 400 at idle ". Or to be precise half the crankshaft speed.
    Regards HMC
  16. Replies
    7
    Views
    1,724

    " so expecting a package delivered today from...

    " so expecting a package delivered today from ilexa here in the UK." Good choice, I am sure Derek would always give advice if you are in trouble. The first thing to do is a full autoscan and save it...
  17. Replies
    6
    Views
    384

    If you do change the brake pads, make sure they...

    If you do change the brake pads, make sure they have anti squeal shims and possibly put some anti seize compound on the back of the pads to act as a damper.
    Regards HMC
  18. Replies
    6
    Views
    384

    Hi Volksrabbit, This is not uncommon, it is...

    Hi Volksrabbit,
    This is not uncommon, it is caused by high frequency vibration of the pad, usually because of lip on the brake disk, sometimes it is agravated by cheap replacement brake pads....
  19. Replies
    6
    Views
    654

    Yes, it was under the drivers seat (RHD) hidden...

    Yes, it was under the drivers seat (RHD) hidden under foam, I had to take the seat out to be able to find it. It was water damaged.
    Regards HMC
  20. Replies
    6
    Views
    202

    "I never fitted the egr but I suspect its...

    "I never fitted the egr but I suspect its aftermarket,"
    In my experience aftermarket has a high failure rate. Who fitted it and why are they not fixing it?
    Regards HMC
  21. Replies
    6
    Views
    202

    Hi judge_360, Was it a genuine EGR? What wiring...

    Hi judge_360,
    Was it a genuine EGR? What wiring checks have you done?
    Regards HMC
  22. Replies
    4
    Views
    364

    Hi Proffa, Have you checked fuses for the engine...

    Hi Proffa,
    Have you checked fuses for the engine management? ECU does not seem to be awake.
    Regards HMC
  23. FOD strikes again! Oh no, not only am I...

    FOD strikes again!
    Oh no, not only am I beginning to understand Jack, I am starting to sound like him. Is there any cure? :)
    HMC
  24. Replies
    16
    Views
    697

    Hi Gremling, Have you actually tried resetting ...

    Hi Gremling,
    Have you actually tried resetting the SRI via Instrument (17) and adaptions? I do not have problems doing, Reset warning to not active, make sure the mileage and distance for oil...
  25. Hi ak77 Let me translate Jack speak into English...

    Hi ak77
    Let me translate Jack speak into English :)
    This could be a faulty Body Control Module or faulty wiring to it, an incorrect bulb may have a different resistance than the correct one and the...
Results 1 to 25 of 152
Page 1 of 7 1 2 3 4