Search:

Type: Posts; User: rbb1485

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    571

    Update! Okay so with my trusty VCDS I viewed the...

    Update! Okay so with my trusty VCDS I viewed the hood switch MBV while I manually depressed the hood switch and the value changed from "OPEN" to "CLOSED" ! Woohoo! I then shut the hood, all doors...
  2. Replies
    22
    Views
    571

    Update! From Dana's recommendation, I removed...

    Update! From Dana's recommendation, I removed the radio and re-seated it. and BOOM! I have power in the signal wire at the hood latch connector! +8V ! I also have ~0.5ohm resistance on the...
  3. Replies
    22
    Views
    571

    Hi Dana, thank you for this ! I will note I...

    Hi Dana, thank you for this ! I will note I recently removed radio from the dash to install the 3-blink "komfortblinker" OEM harness, and I remember struggling a bit to remove the radio, and then...
  4. Replies
    22
    Views
    571

    Hi all, thanks for the feedback! Well on to the...

    Hi all, thanks for the feedback! Well on to the next troubleshoot tests results:
    1) Test T15/1 voltage with respect to ground --> Using my new "back probes" i was able to measure voltage at T15/5 ...
  5. Replies
    22
    Views
    571

    Also, could anyone shine a bit more detail as to...

    Also, could anyone shine a bit more detail as to what the physical connection point of "B161 - Connector (anti-theft warning system) in wiring harness interior" is....looks like.....location....? ...
  6. Replies
    22
    Views
    571

    Hi Zenerdiode, Okay I now understand what...

    Hi Zenerdiode,
    Okay I now understand what "back-probing" is. I was actually wondering that this morning how I am I supposed to test T15/1 voltage at J393 with respect to ground with it still...
  7. Replies
    22
    Views
    571

    Actually, thinking about it more, adding a new...

    Actually, thinking about it more, adding a new ground from a wire tap off of brown T2a/1 wire would not help the situation, as I still do not have voltage present at the T2a/2 pin....correct? Its a...
  8. Replies
    22
    Views
    571

    Hi Zenerdiode, to answer your qeustion, yes it...

    Hi Zenerdiode, to answer your qeustion, yes it is the hood latch switch connector plug near (in my case) passenger side (right) headlight. See photo:
    ...
  9. Replies
    22
    Views
    571

    Thank you Zenerdiode. here are my results:...

    Thank you Zenerdiode. here are my results:
    Test T2a/1 to ground = I am getting around a 5.5ohm resistance.
    Current carrying potential = Incandescent test light LED shows steady "green"
    Short...
  10. Replies
    22
    Views
    571

    Just to provide an update. On my correctly...

    Just to provide an update. On my correctly functioning 03' jetta, when checking voltage with a multi-meter across wires T2a/1 and T2a/2 on the F120 hood latch switch, I get a steady +8V at all...
  11. Replies
    22
    Views
    571

    Hi Uwe, yes that is how I read it as well. So...

    Hi Uwe, yes that is how I read it as well. So what test would you suggest now? Thanks
  12. Replies
    22
    Views
    571

    Hello Uwe, Thank you for your response, truly...

    Hello Uwe,
    Thank you for your response, truly appreciated. I have in fact pulled the wiring diagram from my bently manual, I'll post a pic below. The hood latch switch F120 is a simple 2 wire...
  13. Replies
    22
    Views
    571

    Just to throw up my latest auto scan: ...

    Just to throw up my latest auto scan:


    -------------------------------------------------------------------------------
    Address 16: Steering wheel Labels: 1J0-907-487-A.lbl
    Part No:...
  14. Replies
    22
    Views
    571

    Oh and FYI, on my correctly operating 2003 jetta,...

    Oh and FYI, on my correctly operating 2003 jetta, while viewing measuring block 08 with the hood open, the value shows "open". When I unplugg the connector, it switches to "closed". On my 2005,...
  15. Replies
    22
    Views
    571

    VW 2005 mk4 Jetta - Hood Latch Question

    Hello all,
    So on my 2005 VW Jetta wagon 1.8t I do not get a confirmation "beep" when I lock the car. I first thought it was due to faulty door lock modules because I had signal communication error...
  16. Replies
    1
    Views
    271

    2005 VW Jetta - Disable Seat Belt warning

    Hi there, was wondering if it is possible to disable the seatbelt warning chime on my 2005 VW jetta 1.8t wagon. Here is my auto scan:



    Chassis Type: 1J (9M - VW Jetta IV (1998 > 2014))
    Scan:...
  17. Just to update everyone, I found the /2...

    Just to update everyone, I found the /2 (grey/green) wire broken at the connector, was able to remove the terminal from connector, re-solder, and cleared the code, has not come back yet! Thanks for...
  18. I will confirm N249 is plugged in correctly...

    I will confirm N249 is plugged in correctly tonight, and then perform Jef's ohm test as well, and report back !
    Thanks All
  19. MKIV 2003 Jetta 1.8t AWP - N249 Code Question - P1287

    Hi All,
    So over the weekend, I pulled off one heck of a procedure on my 2003 jetta with 207,xxx miles! It consisted of replacing a cracked exhaust manifold, leaking flex joint on downpipe, and the...
  20. Hey there VCDS community. So since I was unable...

    Hey there VCDS community. So since I was unable to get the gear selection indicator turned off, I wanted to try re-enabling it and then disabling it again to see if that would do anything. Will...
  21. Thanks for the follow up Eric. Dang that is not...

    Thanks for the follow up Eric. Dang that is not the news I wanted to hear! Does any other VCDS gurus have any ideas out there??? Thanks in advance!
  22. Thanks! I will be eager to hear your results.

    Thanks! I will be eager to hear your results.
  23. Do you have any other suggestions for me to try ?...

    Do you have any other suggestions for me to try ? do I have any options? Thanks!
  24. Hi Uwe, I re-checked that the box for gear shift...

    Hi Uwe, I re-checked that the box for gear shift suggestion (active) stayed "un-checked" and it did. So I am assuming it "took" ?
  25. Update! I just took it for a test drive, and it...

    Update! I just took it for a test drive, and it is still showing the gear shift suggestion! What gives ??
Results 1 to 25 of 39
Page 1 of 2 1 2