2005 Passat TDI BHW G28 Sensor Crankshaft speed sensor

   #1  

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
No start. Scan with VCDS does show fault code for failed G28. Multimeter test shows failed sensor. Pin 2 - 3 show infinite resistance. specified 480 - 1000 ohms. short pin 1 - 3. pin 3 - 2 infinite resistance. Question: Why no DTC are shown? Is the programing code in the ECU corrupted?
 

PetrolDave

Verified VCDS User
Verified
Joined
Dec 16, 2014
Messages
4,285
Reaction score
4,265
Location
South Molton, UK
VCDS Serial number
C?ID=1423
Question: Why no DTC are shown? Is the programing code in the ECU corrupted?
Even though no fault codes are shown a full unedited VCDS Auto-Scan is needed as this will help the experts answer your questions.

BTW has your Passat been 'chip tuned' (either by you or any previous owner)? This can often be the cause of DTCs not being shown.
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
These two statements seem contradictory. Perhaps you could elaborate?

-Uwe-
Hi Uwe,
Sorry my mistake . It should read does not show DTC.
Even though no fault codes are shown a full unedited VCDS Auto-Scan is needed as this will help the experts answer your questions.

BTW has your Passat been 'chip tuned' (either by you or any previous owner)? This can often be the cause of DTCs not being shown.

I know the crankshaft sensor is defective because I tested it with a multimeter. But I do not understand why VCDS does not show any DTC related to this failed sensor (G28)
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
Even though no fault codes are shown a full unedited VCDS Auto-Scan is needed as this will help the experts answer your questions.

BTW has your Passat been 'chip tuned' (either by you or any previous owner)? This can often be the cause of DTCs not being shown.
Hi,
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
Hi PetrolDave,
The ECU is stock. It is not tuned. I am the original owner. The ECU was flashed by the dealer so that the 5 volt steel tip glow plugs could be switched out for the 7 volt ceramic tip glow plugs I believe on a recall.
Thanks.
P. Hall
 

Jack@European_Parts

NostraJackAss
Joined
Jan 29, 2014
Messages
21,604
Reaction score
9,128
Location
Montgomery, NY, USA
VCDS Serial number
C?ID=57337
Where is the scan?

CheerfulElegantEyra-max-1mb.gif
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
Hi Jack,
Here is the attached scan. Please ignore the fault codes as I have taken things apart to replace crankshaft speed sensor. Tomorrow I will see if I can get the passat to start. Too dark now to see.
Thanks,
P. Hall
Code:
Wednesday,24,February,2021,16:17:27:54876
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 20.12.0.1 (x64)  HEX-V2 CB: 0.4529.4
Data version: 20201125 DS322.1
www.Ross-Tech.com


VIN: WVWCE63B15E166827   License Plate:


Chassis Type: 3B (3B - VW Passat B5 (1997 > 2005))
Scan: 01 02 03 08 15 16 17 19 35 36 37 46 47 55 56 57 58 75 76 77
        

VIN: WVWCE63B15E166827  
-------------------------------------------------------------------------------
Address 01: Engine        Labels: 038-906-016-BHW.lbl
   Part No SW: 038 997 016 T    HW: 028 101 198 2
   Component: R4 2,0L EDC G000AG  0314 
   Revision: 12345678    Serial number: VWZ7Z0E2003470
   Coding: 0150034
   Shop #: WSC 03107 999 84523
   VCID: 2F3B18F6AB0029B3DA8-5160

6 Faults Found:
19558 - Motor for Intake Manifold Flap (V157)
            P3102 - 000 - No Signal
16791 - EGR Sensor 2
            P0407 - 000 - Signal too Low
16497 - Intake Air Temp. Sensor (G42)
            P0113 - 000 - Signal too High
18000 - Altitude Sensor / Boost Pressure Sensor
            P1592 - 000 - Implausible Correlation
19557 - Motor for Intake Manifold Flap (V157)
            P3101 - 000 - Open or Short to Ground
16622 - Manifold Pressure / Boost Sensor (G31)
            P0238 - 000 - Signal too High
Readiness: 0 0 0 0 0

All of the above faults are because I have taken apart connections etc. to be able to make room for replacing crank sensor.
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
Hi Jack,
No, car ECU is not modified. The ecu is stock. Not sure what you mean by log G28 when cranked. The car is in a no start condition.
Thanks ,
P. Hall
 

Jack@European_Parts

NostraJackAss
Joined
Jan 29, 2014
Messages
21,604
Reaction score
9,128
Location
Montgomery, NY, USA
VCDS Serial number
C?ID=57337

Hi Jack,
No, car ECU is not modified. The ecu is stock. Not sure what you mean by log G28 when cranked. The car is in a no start condition.
Thanks ,

P. Hall

That's debatable Phall ----- US or Canada OBD2 Specs say otherwise!
Clear faults and post a new complete auto-scan unedited please, did you know your thread is inconsistent as Uwe has aforementioned?

Subsystem Redundancy check for FOD in process!

eTu9lha.png


Better JPPSG huh?




G28 is the "engine speed sensor" or "RPM ref sensor" when referencing the RTFB ( Read The Factory Book ) in WD = Wire Diagrams!
 

PetrolDave

Verified VCDS User
Verified
Joined
Dec 16, 2014
Messages
4,285
Reaction score
4,265
Location
South Molton, UK
VCDS Serial number
C?ID=1423
Address 01: Engine Labels: 038-906-016-BHW.lbl
Part No SW: 038 997 016 T HW: 028 101 198 2
Component: R4 2,0L EDC G000AG 0314
Revision: 12345678 Serial number: VWZ7Z0E2003470
Coding: 0150034
Shop #: WSC 03107 999 84523
VCID: 2F3B18F6AB0029B3DA8-5160
Seems unlikely that VAG would use this as the revision code, which makes Jacks suggestion that the ECU has been modified seem very probable.
 

Jack@European_Parts

NostraJackAss
Joined
Jan 29, 2014
Messages
21,604
Reaction score
9,128
Location
Montgomery, NY, USA
VCDS Serial number
C?ID=57337
That and the fact the EGR is ready & before the engine even runs to check it or after re-flash! :popcorn:

This is what is NOT displayed!

Are you going to log G28 OP?

readiness-tdi.png
 

phall1059

Verified VCDS User
Verified
Joined
Jan 6, 2021
Messages
10
Reaction score
2
Location
Lindsay On, Canada
VCDS Serial number
C?ID=424496
Hi Uwe,
The ECU was reflashed at the VW dealer for the 5 Volt glow plugs. As far as I am aware I have never had the ECU tune or flashed. I wonder if the VW dealer made some sort of error.
Regards,
P. Hall
 
Top