Search results

  1. G

    New ABS module. How do I code new module please help

    When I have been at loss for module codes, I looked at the reference threads to find something that matches what I am looking for. That's how I would go about finding the code. This is the link to reference scans. https://forums.ross-tech.com/index.php?forums/45/ Google advanced searching on...
  2. G

    Crazy Audi Fan Here

    Welcome Adam.
  3. G

    I need the long coding for abs module jetta tdi 2014 (MK60EC1)

    When I have been at loss for module codes, I looked at the reference threads to find something that matches what I am looking for. That's how I would go about finding the code. This is the link to reference scans. https://forums.ross-tech.com/index.php?forums/45/ Google advanced searching on...
  4. G

    Security Access Code for HVAC Controller 08

    Epilogue: So the Climatroinc dual zone unit I installed was from the VW China market part number 51G 907 044 K. The unit was slightly different as in place of Max AC button is a Clean Air button and could not change adaptation settings. Since retaining last seat heating value was important to me...
  5. G

    Looking for ABS Module code for 2012 Jetta Sportwagen SE (MK60EC1)

    Congratulations on getting close to the end of what sounds like a really worthwhile project. When I have been at loss for module codes, I looked at the reference threads to find something that matches what I am looking for. That's how I would find the code. This is the link to reference scans...
  6. G

    Audi A6 C6 Battery Drain

    Not saying this is your issue, but it may give you some ideas of looking for micro voltage drops across fuses, and putting a switch in-line of a suspect circuit to isolate. I had a intermittent battery drain that was maddening to troubleshoot. I documented here and the text is below...
  7. G

    A bunch of dash lights today. Yesterday everything was fine.

    At idle, you will read alternator voltage and not battery voltage. I would start by checking the battery, measure battery voltage with car off; then turn car ignition on (do not start) and measure battery voltage (battery under load). I just checked mine which read 12.2V and dipped to 11.9 with...
  8. G

    Security Access Code for HVAC Controller 08

    Unable to access my HVAC 08 controller. I replaced the Climatronic unit with an Auto Climatronic hardware part number 51G 907 044 K. I want to access adaptations to change the retention of drivers seat heater level from 10 min to active, so it keeps last setting when car is started. I tried...
  9. G

    erWIN - Audi

    I apologize I do not recall the specifics of how I downloaded the manuals and schematics as it was a few years ago. Nice option of having an hourly rate as it took me a hour or two to figure things out and download everything I needed.
  10. G

    erWIN - Audi

    I was unaware of an hourly rate, just the daily rate. I had no problem getting all my manuals and schematics in a couple of hours. You already have your logon so it shouldn’t take too long. For the service side which is manuals these are the current prices...
  11. G

    Heated steering wheel retrofit

    Scan likely will not show steering unit as it is not communicating. What is the part number of new steering control module? Did you replace 5Q0 953 549 E with 5Q0 953 549 B? 5Q0 953 549 E does not support heated steering wheel...
  12. G

    Heated steering wheel retrofit

    This post has pinouts of 14 and 16 pin connectors. https://www.vwvortex.com/threads/heated-steering-retrofit.8911169/page-2#post-112126097 With that you can verify pinout. I noted on your scan that it shows Steering Wheel module is communicated with, so this must be your scan before changing...
  13. G

    Heated steering wheel retrofit

    PS: I assume this is the conversion cable you got from Kufatec? https://www.kufatec.com/en/comfort-retrofits/heated-steering-wheel-cable-set-for-vw-skoda-43696 I doubt if the installation instruction provides pinout. If you had the new steering control module pinout you could verify that it...
  14. G

    Heated steering wheel retrofit

    Sorry to hear. Before I suspect the new module, I would verify the power and ground and canbus + and - going from the 16 pin to 14pin connector are going to proper pins power ground and canbus + and - of new clockspring module. I am going to look at a schematic for a Golf to find which pins...
  15. G

    Heated steering wheel retrofit

    This may help or you could reach out to this poster: https://forums.ross-tech.com/index.php?threads/17283/ This person also performed and you may ask: https://www.golfmk7.com/forums/index.php?threads/what-did-you-do-to-your-mk7-today.316916/page-972#post-6570760...
  16. G

    What a story..

    Reference scans of working vehicles are at the below link, you may want to look for another 2009 Passat similarly configured. https://forums.ross-tech.com/index.php?forums/45/
  17. G

    RETROFIT GOLF 7 GTD 2015 WITH MIB1 VS DISCOVER PRO MIB 2.5

    I recently replaced the MIB2 3Q0035844 head unit which I swapped with a 3Q0035844B due to a problem with the unit draining battery https://www.golfmk7.com/forums/index.php?threads/infotainment-unit-draining-battery.379517/ After CP removal and FeC installation, my "driving modes" pop up menu did...
  18. G

    Diagnosing possible optical issue (2017 Golf R)

    Yes, redundant. You have isolated problem, congrats. Now you can move forward on getting it fixed.
  19. G

    Diagnosing possible optical issue (2017 Golf R)

    Pardon, understand they are not completely aligned, but the idea is to use the internal amp in your headunit which will put power to pins connected to nothing rather then having the signal sent via fiber optic to your external amplifier. Copy your current coding settings and save. You will put...
  20. G

    Diagnosing possible optical issue (2017 Golf R)

    You could also code out the external amplifier. If 5F goes into reboot after coding out and reboot, head unit problem is not related to external amplifier. 5F control module, Long coding, Byte 4-7, 2 channel 4 passive speakers, then go to Byte 11 and change to internal sound system (from...
Top