Search results

  1. andyvee

    Logging Advanced Measuring values on 5F

    Hi I wanted to log some advanced measuring values on 5F using the HEX-NET, but I have come across an issue. I can log fine using VCDS on my laptop, here is an extract of what I was logging Sunday,07,February,2016,17:32:52:04069VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64...
  2. andyvee

    Auto Hold function on MQB platform

    Hi experts at Ross-Tech The Golf VII is available with auto hold, the one where when you come to a stop it maintains brake pressure via the ABS unit after you release the footbrake, until you accelerate again. (Not HHC). As I understand it, if you have ACC this means it will hold you...
  3. andyvee

    OBD2 extension cable for HEX-NET

    Hi I'm considering getting a short (1m?) OBD2 extension cable for use with the HEX-NET in Infrastructure mode. I am finding that the location of the OBD2 port on the Octavia 3 means the HEX-NET gets a variable at best wi-fi signal, probably not helped much by the SmartGate wifi module under the...
  4. andyvee

    2015 Skoda Octavia Combi L&K CR150 DSG

    With lots of options ...... Sunday,27,September,2015,19:42:29:16648 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: (x64) Data version: 20150904 VIN: TMBKJ9NE0F0104172 License Plate: Mileage: 26050km-16186mi Repair Order...
  5. andyvee

    2016 Audi S3

    Not my car, so don't know the spec Saturday,31,October,2015,15:35:55:16648 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: (x64) Data version: 20150904 VIN: WAUZZZ8V6GA052459 License Plate: Mileage: 783km-486mi Repair Order...
  6. andyvee

    Changelog for 15.7.2

    Is there one published anywhere, can't seem to find it?
  7. andyvee

    Support for 5F MIB2 Columbus & Amundsen on MY16 Octavia III

    Hi guys Not sure if you are aware, but there are reports of menus disappearing from 5F on MIB2 units on the O3 after enabling some additional menu items. I haven't experienced it myself yet, but there are a couple of reports on Briskoda...
  8. andyvee

    Octavia 3 LED Rear Light Clusters

    These are a straight swap for the originals, the wiring and connectors are the same. These are the adaptation channels that need changing on the BCM Adaptation Channel Standard Lights LED lights (1)-Leuchte20BR LA71-Lasttyp 20 13 - Bremsleuchten 34 - LED Bremsleuchten (8)-Leuchte20BR...
  9. andyvee

    Beta 14.7.0 on MQB

    Hi Used 14.7.0 for the first time on a MQB platform today to code footwell lights as per the below and it immediately generated a fault code that won't clear on 09 BCM 565764 - Program...
  10. andyvee

    Suggestion for improved support for MQB

    Hi I have both VCP and VCDS and there is a significant difference between the two in the way MQB platform support is implemented. With VCP, only one adaptation can be changed at a time, and the controller is reset (rebooted) in between each one. There is also a manual reset of a controller...
  11. andyvee

    MQB Platform tweaks

    All, I have a thread running on for MQB platform tweaks, the ones on Briskoda have been tried and tested on the Octavia III (5E). You can find the thread here If anyone has anything further...