Search results

"Filled a balloon 🎈 " ?? It's a vacuume pump not a pressure pump. Totally opposite.

Hello all, This weekend I'm planning on doing a carbon clean and take out the injectors and clean and test them . I have a gdi injector cleaner. I have 12 injectors and intend on testing for flow and if I find any discrepancys I will switch the offending injectors. My question is if I switch...

Correct, but the original question was "would the abs fault cause the service reminder to NOT REMIND ME of a 5k service due to the fact that the odometer is not able to record milage during the abs fault?

I should also mention that when the ABS module failed that causes other systems to stop working. Such as cruise control and the speedometer. Now the speedometer is simply reading zero all the time and because of that zero miles are added to the odometer even though the car was driven approx 500...

I don't understand EXACTLY what your asking for. I believe that the SRI info was added to my log file that I posted above directly after UWE posted his first post. It is located at the very end of that file, aka scroll down to see it. It was added 4 times at the end of that log file , as I...

My apologies. I didn't think that the Sri file was added. I did click it 4 times. Perhaps a notification saying " SRI file added to scan" would have clarified that for the newbies....

Tuesday,10,June,2025,21:27:36:15949 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 11 x64 VCDS Version: 25.3.1.1 (x64) HEX-V2 CB: 0.4671.4 Data version: 20250415 DS365.0 www.Ross-Tech.com VIN: WAUDH78EX7A103186 License Plate: Mileage: 297890km-185100mi Repair Order...

So I set my service interval to 5k miles and it worked and notified me at 5k miles. I then used vcds to reset it and during the next 5k miles my abs pump failed and I replaced that 5 times until I figured out what was wrong. The problem was a bad connection on the back of the instrument cluster...

https://photos.app.goo.gl/4uL1FgX26YCr5iMW8 This is the vacuume check valve that is located righr at the top of the vacuume pump. This check vslve was bad and caused all my issues with check engine lights. Problem solved. P.s. The pliers in the photo are used to remove fuel and vacuume lines...

306mBar

I should have also mentioned that I did the resistance test using the 3 pins on the LDP as you stated and recieved results within the specs. I did this on both pumps and both passed. I also had power and ground on that connector going to the LDP. I also should ha e mentioned this: every time...

009218 - EVAP Leak Detection Pump Control Circuit P2402 I've done a smoke test and saw no leaks. I went into the vcds under 1 aka engine, and did an ouput test and the n80 and leak detection pump, located behind right rear inner fender, both tested ok. But the test tested it 60...

More updates: ABS module fails again. Get another one off ebay. Car won't detect it. I send a bad one out to get repaired and the repair company tells me that it's beyond repairable. So i Order a remanufactured one. Car won't detect it. So I start verifying that the bundle of wires are all in...

Perhaps I can simplify my question with more detail. Let's say u have 2 pending mils. We'll call them mil A and mil B . Both mils require multiple Faults to trigger the mil light. I'm not too concerned about what causes it just the amount of failures adding up. So say mil A and B are triggered...

Hopefully this is a simple question. There are many mil lights, aka check engine lights. Some are triggered after one fault and others are triggered after several. For clairty let's say 4 fails out of 10 tests causes the mil to light up. So, if I clear fault codes does this reset the triggers...

Update, So as posted above, I installed the used abs module with the same results as the original abs module, aka, it doesn't show up under address 03 or anywhere in the vcds scan. But there are plenty of codes looking for it. So off to the Bently wire diagrams I go. As I'm searching through the...

Hello UWE And Dr Sheldon, After looking through many pages of the Bently manual, in the wiring diagrams there is K-line lo and K-line hi. Perhaps that's how it's designated?

That's easier said than done. I have the wiring diagrams. My issue is the location of the connector at the abs module and the routing of the cable. I can't just pull the abs module out alittle to gain access because the brake lines are attached. Access is restricted. Note the car has a v6 3.2...

Did the ABS control module reconditioning fix the issue? Where did you send it for reconditioning?

UPDATE: ok I got a used ABS control module and installed it today. I have the same errors as originally posted. Whats my next step? Many questions. 1- There is also a code for vehicle speed sensor. But for the life of me i cannot figure out which one it is? 2-address 08 What is HVAC ? Heating...