Search results

thanks to all the replies above. i've subsequent done some research on how MQB platform vehicles control external lights, and whilst i have a better idea now, however i'm not 100% sure. My plan now is to use an unused BCM channel (i only need 1 channel/wire for this purpose), set Lichtfunktion...

I had feeling that would b the case, hence I wasn't too confident on the tapping/splicing approach. I'll have to do my homework with the BCM approach.

Thanks @Uwe Yeah, that would b the ideal way to do it, by connecting to the BCM directly. Is there an easy way to determine unused BCM outputs? I've got an OBDEleven device. I did some more reading up on how people retrofitted the VW light bar and illuminated badge, and someone mentioned...

Details of my modules.... 09 Central Electrics System description: BCM MQBAB H Software number: 5Q0937084CG Software version: 0236 Hardware number: 5Q0937084CG Hardware version: H34 19 Gateway System description: GW MQB High Software number: 3Q0907530AA Software version: 5366 Hardware number...

Hi Folks, Hoping someone can shed some light here. Essentially i have a project that i'm looking at doing that involves adding an additional LED strip, that will behave just like the factory DRLs, i.e. full brightness and dim. when the factory DRLs r at full power, the additional LED strip...

don't know if this plays a factor, or if i'm barking up the wrong tree - but the TPMS module doesn't give out any readings until the car has been driven a few meters - i.e. the tire sensors have had a number of revolutions. hence simply giving the TPMS module power is not going give any pressure...

when i retrofitted direct TPMS to my Superb B8, i did the following changes below. hope this helps. p.s. i didn't enter any security code for Controller 03 ABS. Enable Direct TPMS from Gateway Controller 19 – CAN Gateway Security Access - enter 20103 Click “Installation List” Activate “65 -...

thanks @kamold :thumbs: i did read about that PSD thing, but wasn't able to find concrete info on it. sounds like i just need to stick with TSR in "road sign detection" mode, and using Waze in Android Auto. its a good combo, just the annoying TSR warning message to contend with at each...

i've been trying to crack this mystery too @Dixon, but with no luck so far. i enabled TSR on my Skoda Superb MY17 a while ago, however its not working in fusion mode. i followed these steps:- Controller 5F - Information Electric Adaptations...

this is the current default behaviour in my Skoda Superb MY17, with DSG-6. with start/stop active, and auto-hold active, the car will not restart, after coming to a stop, until i tap the accelerator, or i wiggle the steering wheel. i've been driving my Superb like this for 4+ years, since Day...

i recently retrofitted the Direct TPMS to my Skoda Superb MY17. i followed the instructions for retrofitting this to a mk7 Golf. this is wat i have:- ------------------------------------------------------------------------------- Address 65: Tire Pressure (J502) Labels: 3AA-907-273.clb...

it pulses when the door is unlocked and ignition is off. doesn't pulse while the engine or start/stop is running.

Try either of these security codes:- - 20103 - 25327

does the same thing in my car (MY17 Skoda Superb). interior lights don't illuminate until a door is opened. ignition off does nothing. likewise, infotainment remains on until a door is opened. previous MY11 Skoda Octavia would illuminate interior lights as soon as ignition is turned off...

I did the following to keep my instrument cluster illuminated at all times. I have a Skoda Superb, but it might also work for u, as I got it from a guy who did this on his mk7 Golf. Controller 17 - Instrument 16 - Security Access - enter 47115 10 - Adaptations Go to: dimming characteristic...

I fitted a Start-stop memory device in my Superb (MY17). It's perfect for me. It remembers the last state of the start-stop when u turn off the car. So the next time u start the car, start-stop retains the previous state. No fluffing around with voltages. I can still use the start-stop function...

Thank you. Yes, that is the unit part number. I put it on the left side because:- - the BCM module is on the left side - the TPMS's wire length is not long enough if placed on the right side - the guides show placement on the left side. My preference was to mount it behind the bumper, so it's...

It's all working now - thanks for ur help. It's tapped to Fuse location 30, and I've run the wiring under the door sill trim. The TPMS module was already parameterized, so there was no need for me to use VCP to get it working. However, I'll need to update the parameter file so it has the...

Unfortunately my plans to piggyback of Fuse #44 (trailer) is hampered due to the extra tall pink fuse in location #43 :( My concern with Fuse #7 is that a number of things will reset or loose settings if I pull the fuse. Fuse #7 is responsible for Air conditioning, heating, receiver for the...

mine definitely has the trailer hitch preparation, which I verified using Erwin Skoda to get the vehicle build report of all the PR-codes based on my VIN number. it has "1D7 - Trailer Hitch Preparation" listed (see screenshot below). this is the wiring harness from the front to the back. it...