Search results

  1. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    You know what. I'm over your unjustified disrespectful comments. And you started that bullshit on Day 1. So....go fuck yourself
  2. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    If i remove the J533 and put on my bench to code it, yes I can communicate with it that way. If it shouldnt take this much effort, then please tell me the next step, because im lost. I see 12v on the can wires and I know that is not good and I believe that is what I cannot communicate with it...
  3. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    IT WONT LET ME POST PICTURE OF SCOPE MEASURING THE SAME VOLTAGES ON THE CAN LINES YOU SAY i CANNOT. BUT THE VOLTAGES AREN THERE EVEN ON THE SCOPE
  4. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    it is a big ask. Do you know how to code the J533? You have too REMOVE the J533 from the vehicle. Then connect the powers (15 and 30), ground, and Can wires to the J533 PINS. How the hell can I do that if the pins are connected to the F'n car? You cant measure voltages on Can wires? Most...
  5. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    Ummm you DID write to de-pin all pins except the ones you noted on post #17. The ones you said to keep connected on the J533 are pins: 1, 9, 11, 14, 19; so the OBDII is connected solely to the J533. Which is EXACTLY what i did. Where is the misunderstanding? I did that and still have no comms...
  6. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    You didnt say to keep pins 1, 9, 11, 14, and 19 connected?!?!? If those are not connected, how inn the hell could I even try to communicate with the J533? doesnt it depend on what the car is equipped with?
  7. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    Ok, just to make sure I understand your procedure clearly........ Step 1. De-pin all pins from the J533 except the ones you noted to keep connected Step 2. Hook up VCDS and try to communicate with the J533 directly and solely with the J533 (isolating all can networks except the circuit that...
  8. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    I honestly cant remember, it was 5 years ago. but I did just download the irwin wiring diagrams for the ecu, J519, J533, D9 and they are identical to how its wired currently.
  9. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    ITS A GIFT WHEN THAT GUIDANCE IS SMOTHERED IN SARCASM
  10. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    I DOWNLOADED FROM IRWIN THE WIRING DIAGRAMS AND THEY MATCH UP TO MY WS MANUAL TO A 'T'. SO THE ECU IS WIRED CORRECTLY.
  11. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    NO, THERE IS NO SECRET INFORMATION THAT IM NOT PROVIDING. HOW WOULD THAT HELP THE SITUATION?
  12. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    THE INFO YOU GAVE ME HAD DISCREPANCIES THAT I RELAYED TO YOU BUT DID IT ANYWAY. STILL NO COMMS! SO HOW DO YOU PROPOSE I "ESTABLISH COMMUNICATIONS" WITH THE GATEWAY?
  13. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    You said which wires to leave connected to the J533 and see if I have communication. I did what you said and nothing changed. I don't recall your next step from that? I have to go to a job right now and when back, I'll scroll through and and see if I missed your next step. If I did, I'll do it...
  14. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    And if I don't have the correct wiring diagram and you or anyone here does have it, can I see it? At least I could double check each wire into the ECU wiring. If it's wrong, I will fix it. But at least I can remove that possibility from the equation.
  15. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    Right, so tell me what I'm doing wrong. The ECU is pinned iaw the factory wiring diagram, at least the one I have. I have voltage on the can network where I should not, which could be the cause of all of this. But I have no idea where that voltage is coming from. Almost as if the ECU is...
  16. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    Huh that strange, I couldnt find these "Multiple " comments "over the last 4 pages" saying that I have incorrect wiring diagrams. the first time I seen or heard it was couple comments go after I posted a picture. By the way, I wired it up this last time in accordance with the Workshop and...
  17. H

    Can I get the code from a J519 - Onboard Supply Control Unit

    Try again? Does smart ass run rampant on this site? What's "FSM" stand for? Maybe I'm wrong but assumed it meant factory service manual. Never used "sumdata" but I've used Mitchell a lot and it looks nothing like the Mitchell website I've used. Those pictures are out of "FSM-VW-CC-SERVICE AND...
Back
Top