Search results

  1. A

    2004 Audi TT 3.2 - Check milage with VCDS-Lite

    Excellent, that worked. Thank you.
  2. A

    2004 Audi TT 3.2 - Check milage with VCDS-Lite

    Hello, my TT's instrument cluster LCD is damaged and the milage is not legible. I own VCDS-Lite, is it possible to check the milage with this version of the software? I've watched YT videos showing this with the full version of VCDS, but the same options are not available to me with VCDS-Lite...
  3. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    @Jack@European_Parts thank you for taking the time to do a remote test session with me last night. For others that may have similar issues with this engine, we ran the 200 block macro test and was able to get a P0420 fault on the cat. After some further testing, we discovered that the amplitude...
  4. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    Hi @Jack@European_Parts are you referencing this contact form on your website? I can set up a zoom meeting or google hangout if that works. The car has a full battery charge and I will be able to connect with you remotely and give you control of my pc connected to the car.
  5. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    Sorry for the delay in my reply, been tied up with work. I did all the tests that were suggested, still the same result. @Jack@European_Parts I would appreciate a remote session if you are still up for it. Please let me know what day/time works for you, I'm in the pacific timezone.
  6. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    @Jack@European_Parts Thank you for your continued support with my issue. I went through the various tests I found on this forum 30-46 and 70, 71, and 77. I was not aware there is an actual readiness script I can run. I have not attempted to recode the default controller. I will be testing the...
  7. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    I've confirmed the car has a factory MAF and after clearing all the codes and running through all the readiness steps here is the auto scan log: VCDS-Lite Version: Release 1.2 Wednesday, 23 September 2020, 19:30:14:52212 Chassis Type: 8N - Audi TT Scan...
  8. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    I have since reset all codes and ran through the readiness script again. At the moment, the catalyst is the only one not ready. I will post another auto scan and screenshot of the readiness screen later today. thank you again for your continued support.
  9. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    I’m no expert, hence why I’m here seeking help, but the cat conversion readout seems accurate (under .50). I’m trying to understand why the test in 46/47 runs the turns off after a minute or so. It does not give me any faults. Would really appreciate some help if anyone else has experienced this...
  10. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    Not to my knowledge. The vehicle was purchased from a salvage yard with a bad engine, I swapped in a low milage engine and replaced the cats and all sensors. The readiness monitors only show catalyst incomplete. How would I process firmware updates? And can you please explain what you mean by...
  11. A

    Catalytic Converter - reset "readiness" for emission tests on 2005 Audi TT 3.2

    Hello, this is thread is 4 years old but I’m having a similar issue and was hoping someone can help me. I’ve set all the readiness monitors on my 2004 Audi TT 3.2 except for the catalyst monitor. I recently installed brand new cats after months of being unable to pass the cat. Test 46/47 turn on...
Back
Top