Search results

  1. Z

    Parking sensor fault

    Hello Dana thank you for your time helping me solve this problem i found the corect coding for abs module but the lenght of the coding (the corect one is too short)it is not the same so i can not code abs with that coding i will post them later
  2. Z

    Parking sensor fault

    Write from old module but i think someone before me mess abs coding
  3. Z

    Parking sensor fault

    No the car was flooded and replaced control units with original part numbers
  4. Z

    Parking sensor fault

    Hello guys i have audi tt with parking sensor problem the sensors are working but i get message on instrument cluster (parking aid fault obstacles cannot be detected)the graphic of the car is shown obtacles are detected but the message does not dissapear.did someone had a simmilar situation and...
  5. Z

    Retrofit ccs golf mk 7

    I will check tommorow on a working car and i will post indivualisation characteristic
  6. Z

    Retrofit ccs golf mk 7

    here it is ;SW:3Q0-907-530-AA HW:3Q0-907-530-C --- CAN Gateway --- SA: 20103 ;Component:GW MQB High 442 4368, Coding:030100F42F087300CB0002581C0F00010001070000000000000000000000 ;EV_GatewNF,013025,EV_GatewNF_VW37.rod ;Wednesday,23,August,2023,21:58:31:47642 ;VCDS Version: Release 23.3.1...
  7. Z

    Retrofit ccs golf mk 7

    Boki can you attach photos? FEC activ:
  8. Z

    Retrofit ccs golf mk 7

    Yes you are right but i check in gateway fec status and for ccs it says that is activated and i put the gateway in a car that have ccs and done fec restore and fec ccs status says that is active i can take pic and post it
  9. Z

    Retrofit ccs golf mk 7

    Hello i want to retrofit ccs standard cruise control on golf mk 7 2014 1.6 tdi, i have replace accelerator pedal,high gateway with enabled fec for cruise, steering wheel with mfsw i place wire between j527 pin 5 and engine control unit j623 pin 46 do the coding in gateway adaption ccs mfsw...
  10. Z

    Resolved ABS coding (ESP MQBA0)

    The coding was accepted thanks
  11. Z

    Resolved ABS coding (ESP MQBA0)

    I check in etka also and it is aa and the car has i think only front assist without acc
  12. Z

    Resolved ABS coding (ESP MQBA0)

    The car had accident and someone replace abs and did the coding that is right now i tried online with odis but odis get error brake electronics could not be coded the part number i check is for the vehicle in short that is so if someone could compute right coding i will be appricieted thanks
  13. Z

    Resolved ABS coding (ESP MQBA0)

    Hello i have ibiza 2018 with abs coding wrong code so can someone could help me and post me coding thanks in advance Saturday,08,July,2023,13:36:25:47642 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 23.3.1.0 (x64) HEX-NET2 CB: 0.4631.5 Data version: 20230421...
  14. Z

    Toolbox opens, but can't see/find it on the screen?

    Hi i see now about the solution that worked for me too but now some buttons are missed like long coding helper ……
  15. Z

    Toolbox opens, but can't see/find it on the screen?

    Thanks Uwe i try it but without success
  16. Z

    Toolbox opens, but can't see/find it on the screen?

    When you press on vcds toolbox it opens window but actualy there is no window if i go to task manager and click on and press maximize window only black screen apear i check od another pc it is the same i can post a pic later
  17. Z

    Toolbox opens, but can't see/find it on the screen?

    Hello does anybody have problem with vcds toolbox after update to 23.3.1?
  18. Z

    Update 22.3 and it is not comunicate with car and dont want to do firmware update

    it is the same it says you need a firmware update and if i check it says that the firmware is up to date
  19. Z

    Update 22.3 and it is not comunicate with car and dont want to do firmware update

    Hello i have a hex net interface and i updated to latest version 22.3 after that when i open vcds i did test interface and it required firmware update i click ok and start to checking for firmware update it says you are up to date but when i try to connect with car i got message (failure to...
Back
Top