Search results

  1. S

    Passat Alltrack Easy open retrofit...

    Read out the dataset and went for a drive.. Now it's working... Maybe I'll use it more than the head-up display :thumbs:
  2. S

    Passat Alltrack Easy open retrofit...

    Yes, that radio menu is getting full :D It is calibrated, proximity sensors register whatever I put in there and still won´t open the hatch.. Been living in the car for some days now (retrofitting alarm/tilt and easy open), hope nobody will see me kicking the bumber today.. :eek:
  3. S

    Passat Alltrack Easy open retrofit...

    Should I return "ENG126956-ENG142121-Byte9_VIP-vip_activation_on_clamp15,not activated ,1" to activated?
  4. S

    Passat Alltrack Easy open retrofit...

    All that I could find: FE is without easy close? 1C, 1B, 2D, 2F, 22, 23, 26, 28, 36, 62.. But now it`s calibrated and still not working, kicking the car does not work. Easy_open_unavailable_reason "No_kick_detected" But both sensors registers my foot when looking at them in "Measured values"...
  5. S

    Passat Alltrack Easy open retrofit...

    In measured values: Easy_open_unavailable_reason $10BE Vehicle_type_unknown..
  6. S

    Passat Alltrack Easy open retrofit...

    Thank you.. Copied all your settings, but still "Vehicle type unknown".. Should I just run the VIP output test anyway (I have tried, many times with VCDS)?
  7. S

    Passat Alltrack Easy open retrofit...

    Whatever I write in IDE10845 I get "Vehicle type unknown" and now im back to 1B and it still say unknown.. Thursday,17,October,2024,12:23:03:54229 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 24.9.1.0 (x64) HEX-NET2 CB: 0.4656.5 Data version: 20240926 DS359.0...
  8. S

    Passat Alltrack 2017 2Q0 camera retrofit

    To get TJA, I had to change from VW to Skoda... Lane assist icon does not show on VC1 clusters, even with the latest version 4191..
  9. S

    Passat Alltrack 2017 2Q0 camera retrofit

    Yes please :)
  10. S

    Passat Alltrack 2017 2Q0 camera retrofit

    Ok, removed pedestrian from 5F and 17 (+FCW) and for 3-ABS I had to untick: Byte 28 Bit 3 FCWP... Does anybody know how to get the lane assist icon to show? Now I only get the white lines.. Also (because of icon problem) TJA not working!?!? I think :) Shall I activate ADLW? Or is this only...
  11. S

    Passat Alltrack 2017 2Q0 camera retrofit

    Will have another look at this today, thank you...
  12. S

    Passat Alltrack 2017 2Q0 camera retrofit

    I don't want to remove "safety" functions.. 100E1700 is activated.. But how do I get FCW (Forward Collision Warning?) working?
  13. S

    Passat Alltrack 2017 2Q0 camera retrofit

    Retrofitted 2Q0980653C 1304 camera and can`t figure out how to remove these DTC`s... Had a 3Q0980653 camera with pedestrian assist, is this the problem? Friday,13,September,2024,17:43:05:54229 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 24.5.0.0 (x64)...
  14. S

    Delete Heated steering wheel

    Not that I know.. But it does not matter, just a DTC...
  15. S

    VW Passat B8 2018 aux heater and climatronic control over infotainment display

    Upload your admap for 5F Atleast what you should have in 5F: ENG122227-ENG117531-Car_Function_Adaptations_Gen2-menu_display_auxiliary_heating,activated ,60 ENG122227-ENG117535-Car_Function_Adaptations_Gen2-menu_display_auxiliary_heating_after_disclaimer,not activated ,60...
  16. S

    Delete Heated steering wheel

    You have to change your steering wheel control module to a non heated version...
  17. S

    Golf 7 swapped AID for analog.. MOST problem..

    That did it golfi_vend.. Thank you..
  18. S

    Golf 7 swapped AID for analog.. MOST problem..

    As the car has Dynaudio amp it needs MOST on in byte 19. I have tried the old coding that was used before fitting AID and it does not remove the MOST dtc.. ;SW:5NA-035-020-D HW:5NA-035-020 --- Information Electr. ;Component:MU-H-ND-EU H54 1367...
  19. S

    2011 Q7 - Westfalia Tow bar Electrics Coding

    Post a complete scan.. Just retrofitted westfalia yesterday, and there is no problem connecting to it or coding it.. Tried with both 2009 and a 2016 module..
  20. S

    Golf 7 swapped AID for analog.. MOST problem..

    The R cluster is back in and AID is out, wife liked it better with analog clocks.. But I cannot find the solution for this MOST/optical dtc on 5F.. MOST "cables" have been removed and the Dynaudio is working just fine :) Tried every AID retrofit guide backwards, but still not able to remove this...
Back
Top