Search results

Hi guys I've uses IE11 for many years for surfing and this forum. I click on the forum yesterday it shows a massage. RC4 cipher is no longer supported in Internet Explorer 11 or Microsoft Edge I've check the RC4 settings in Internet Options and they are ok. I've Googled this problem and on...

Ok so which model was shown for that AutoScan?

Chassis Type: AU-VW37 (3Q0) AutoScan.txt doesn't list 3Q or Alltrack are you using your works VCDS? BA,VW Golf Variant VII (2014 >),00

Hi guys. I use a lot of forums over the past few weeks these forums have changed to https. I use IE11 for my main browser and Firefox as a backup. When I open these forums a message pops up at the bottom saying Only secure content is displayed which I ignore as the forum shows everything and...

2007 Passat 1.9 TDI won't go up a hill only wiithout Limp Mode Hi Guys/gals. I have a friend who lives local with this problem with her 2007 Passat 1.9 TDI-PD BXE. It only goes up a hill the Malfunction Indicator Lamp (MIL)(K83) comes on. If the car stops and the turn the ignition off. Start...

Hi guys/gals. How does VCDS find the engine code in log file, from the ecu? When I scan my Golf GTD it shows: Address 01: Engine (CBB) Labels: 03L-906-022-CBA.clb I know its abbreviated from CBBB. It shows CBB on the timing belt cover again why do VW abbreviated it? Older vehicle scans all...

Hi guys/gals. There are a lot of codes on Ross-Tech Wiki. e.g. http://wiki.ross-tech.com/wiki/index.php/16787/P0403/001027 That says: Possible Solutions Check Fuse(s) Check Wiring and/or Connector(s) from/to Exhaust Gas Recirculation (EGR) Valve (N18) Check/Replace Exhaust Gas...

It isn't only a Mk6 Golf problem as the same type of light is fitted to other models. I've had an error code for a few months. The indictor strip light works on both mirrors so I haven't really bothered about it. Last week I noticed the light in the drivers door the one with the fault code...

This is not a forum feedback but Ross-Tech Wiki. You can move this thread if you want too? I've just done a scan on a 2008 Skoda Octavia 1.9 TDI and its come back with error codes which I can post the full AutoScan if needed. This is the one that needs more info...

Hi guys. I know I added my comments to a couple of other threads on the same subject, with no real solution, so I may as well make my own thread. Help, no response from (CAN) Gateway 2016 Skoda Fabia & Citygo not DTC scan I installed the new VCDS Release 16.8.0 the other day and I've just...

Chassis Type: AU (5Q0) Scan: 01 02 03 05 08 09 10 13 15 16 17 19 22 2B 42 44 47 52 55 5F A9 Your using AU chassis Type: AutoScan.txt shows: AU,VW Golf/Jetta VII NAR (2015 >),00 when your in Sweden!!! Scan: 01 02 03 05 08 09 10 13 15 16 17 19 22 2B 42 44 47 52 55 5F A9 I've always used 1K for...

I have a 2008 Passat 2.0 TDI with a few faults. I tried to get basic setting for G200 sensor. http://wiki.ross-tech.com/wiki/index.php/VW_Tiguan_(5N)_Brake_Electronics#Basic_Setting It only shows Adjustment of rotational rate & lateral/longit acc sensor (G200/G202/G251) - 061 error not...

I install all new updates when they come out. Last month after VCDS Release 14.10.1 I did a scan just to try it out and it stopped responding so I had to End Task it after a couple of minutes. It only scanned down to Address 17: Instruments (J285) Labels: 5K0-920-xxx-17.clb then stopped. I...

Its strange you have these two I have. 008583 - Bank 1; System too Lean at Idle P2187 - 004 - - MIL ON http://wiki.ross-tech.com/wiki/index.php/18619/P2187/008583 VAG Error Code: 008585 EOBD II Error Code: P2189 Fault Location: System too Lean at Idle, Bank 2 Possible Cause: Malfunction...

Hi guys. I've just plugged it in to do my normal scan VCDS Release 14.10.0 after it finished I thought I would give the VCDS Beta 14.9.0 ago. All buttons were disabled and a message at the top said it out of date. I went online the http://www.ross-tech.com/vcds/download/beta/current.html and...

Hi guys. On Ross-Tech Wiki e.g. 00200 http://wiki.ross-tech.com/wiki/index.php?title=Special%3ASearch&profile=default&search=00200&fulltext=Search it says Create the page "00200" on this wiki! http://wiki.ross-tech.com/wiki/index.php/00200 it says: It would be nice to create this code but...

When you install all versions of VCDS and Beta it installs the USB drivers separately make sure you click on it. Now the strange thing is its lists the normal and Beta USB drivers separately in Programs and Features. Windows Driver Package - Ross-Tech USB Driver Package (05/12/2014 2.10.00)...

Yes I have the HEX-USB+CAN interface. It definitely said 9.2 then 9.3 after the update. I've installed all Beta versions since they came out and that the first time I've seen that message. No I'm having no problems with standard VCDS Release 12.12.3 or VCDS Beta 14.8.1 I just wondered why I...

I downloaded the current VCDS Beta 14.8.1 on the 13th and I installed it. The next day I plugged it in and went to Options\Test and it said I need to update the version, I clicked on update. It said current version 9.2 update 9.3.

I've noticed that Technical Service Bulletins (TSB) and Technical Product Information (TPI) don't show up.