Search results

Thanks for the advice Derek. Have tried to set RHD in the engine controller and get the following rejection from VCDS I've also unticked the RHD command within both the 09 Central Electronics module and 19 Can Gateway, but this setting results in an error code 00944 databus implausible in the...

Thanks for the further input, I've managed to pull some additional information from the controllers tonight. I've done a general trawl of every bit range of each controller, looking for any reference to Cruise Control or RHD - the results are the first 4 snippets below I've also done a few logs...

So, spent another 5 hrs doing cross check after cross check yesterday evening. Have checked cable continuity end to end of the new loom, and all are good, I've run live data on the engine module, and this confirms the stalk switch position is recorded accurately in the on or off positions...

Derek, you were spot on with your experience, it was a loose connection at the rear of the socket preventing me from reading the car. Finally managed to get back onto the controllers and have done a couple of checks though all the current settings and found that the U111200 code being thrown up...

Hi Derek, What's the location of pins 6 & 14 in the OBD port?

Sorry, it was Friday evening I managed to scan the Seat, the scan is below. I also managed to clear the fault codes on this car, albeit this is one that I've been trying to cure of faults for over 12 months now, but I'll save that for another thread! Friday,08,November,2024,20:01:34:65142 VCDS...

Hi Derek, yes I managed to connect onto another VW group car yesterday without any issue (Seat Ibiza with identical engine as the Skoda)

Hi there, I've connected to the car again with OBDEleven, and have managed to pull the following coding histories from it, which may or may not provide a further insight into whatever is happening with the CAN and possibly affecting VCDS from connecting correctly. Data logs and history taken...

This may be a daft question, and those with way more knowledge of the various methodologies available for coding vehicles, but if VCDS, OBD 11 and Carista can all change the output modes of the controllers, do they not all operate on the same protocols?, and therefore should it / does it matter...

Not ticked, but tried connecting again and got a slightly different response - today the status was CAN :OK, but still couldn't get a connection to any controller

Everything I've got & read by way of identifying information suggests that it is a 2013 MY vehicle

Hi there, I've been doing a couple of retrofit add-ons to my sons 2013 Skoda Fabia Monte Carlo, including adding cruise control and a Multi Function Steering Wheel. He's only had the car 8 weeks now, but it was bought from his uncle, was well kept and only had a couple of random issues with the...

Just want to confirm I followed up on siLc's advice, purchased a used AH version module and all is now resolved!

Hi SiLc, appreciate the response. I have looked through the other control module versions but just wanted a sanity check before committing to purchase new parts as most often electronics can't be returned if they turn out to have been incorrectly ordered!

Thanks for the heads up Bruce, scan as requested! One thing to note, the squib ring has failed hence the faults logged in section 16! ================================================= Wednesday,06,September,2023,19:13:14:65142 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64...

Hi there, I'm looking to retrofit a cruise control upgrade to my daughters 2011 Eos Exclusive and need a bit of help with confirming the correct selection of the steering wheel control module required to be installed for the retrofit. As original fit, her car has steering wheel control module...

Apologies for the ridiculously long delay in getting back into the forum! I'm a little confused with the statement 'are you quite sure that 5K0 953 569 AL is an appropriate replacement for 1K5-953-521 AH' Am I being dim here, but I read the 1K5 953 521H reference as a software code as it's...

Hi there, I'm new to the forum, as well as to VCDS, but i'm always up for learning a new skill when it concerns vehicles, and as we currently have 4 VW stable cars in the family it seemed to make sense to dig a little deeper into how to be able to do a few home maintenance items when the needs...