Search results

  1. MVB

    MK5 Golf ABS Implausible Signal

    Not sure how the recall worked in the UK but here in the US the recall was for a software update and if after the software update they got certain Dtc they would replace ABS module at that point. If these certain Dtc come up at a later date they will replace the ABS module for free. You have...
  2. MVB

    Golf mk5 Starting issues

    May want to try a new ignition starter switch with the codes you have for it.
  3. MVB

    Auto-scan results

    So the rear doors were not checked as previously stated:confused:
  4. MVB

    Auto-scan results

    Did you miss Uwe reply to my post.
  5. MVB

    Auto-scan results

    OK, so you have at least 2 modules that are not being seen in the scan, you should be able to go to the CAN module and check the boxes for [62] Door Electronics (Rear Left) & [72] Door Electronics (Rear Right). Make a new Auto-Scan and post it back up.
  6. MVB

    Auto-scan results

    Thanks for the complete post. Is this a 2 door or 4 door??
  7. MVB

    Auto-scan results

    Can you please post up a complete uncut Auto-Scan so we can tell what type of vehicle your are working on.
  8. MVB

    Problem with ESP MK60EC1 fault 01130

    Please check if you are part of a recall for the ABS "On vehicles with ABS/ESC the earth connection may be interrupted. This may cause failure of the ABS/ESC system" You currently have a code that VW need to see after doing a software update to make replacement of the module under the recall.
  9. MVB

    2009 VW Rabbit ABS Module Change with Code Rejected Error 12

    So the recall was done in 2017 and software installed and a scan was made and you did not get the codes that VW looks for to replace the module right there, a few years later you get one of the two codes VW looks for, your first scan clearly show one of the two codes that would qualify for...
  10. MVB

    2009 VW Rabbit ABS Module Change with Code Rejected Error 12

    It take it if the recall was performed on this car it would not show up as needing a recall on that site. Do you not have the paper work for the recall they did that you mentioned? They are also supposed to place a label on the core support to indicate recall was done. Any dealer or VW...
  11. MVB

    2009 VW Rabbit ABS Module Change with Code Rejected Error 12

    https://static.nhtsa.gov/odi/rcl/2016/RCRIT-16V913-6017.pdf Page 5 has the sample letter that was sent out. Not sure what they will do for you now that you have removed the original module/pump that may or may not have had the codes that they look for before they will do a replacement.
  12. MVB

    2009 VW Rabbit ABS Module Change with Code Rejected Error 12

    So the dealer / VW denied to replace module after they did the software update and the module failed at a later date. "To help correct this defect, your authorized Volkswagen dealer will update the ABS control module software with improved diagnostic capability to detect insufficient PCU ground...
  13. MVB

    2009 Volkswagen Jetta Problems

    Interesting that the code you have and the freeze frame data on the fourth line of 125 is what VW uses to replace the module after doing the software update under the recall.
  14. MVB

    2009 Volkswagen Jetta Secondary Air Injection system

    Not sure what the Maryland VEIP will accept as proof , as a start you could go to the dealer and ask them to print out the Vehicle Data Information sheet that will show exactly how the car was built by Vw.
  15. MVB

    2009 Volkswagen Jetta Secondary Air Injection system

    If its this car in your scans no it did not have SAI because your engine code is CCTA. https://forums.ross-tech.com/index.php?threads/25729/
  16. MVB

    2009 Volkswagen Jetta Secondary Air Injection system

    If your engine code is CBFA it came with SAI.
  17. MVB

    Fuel rail pressure fluctuations

    Looks normal to me This is a Log in 3rd to redline...
  18. MVB

    Looking for WD for tail lights for MK5 Jetta ROW

    Still looking for a ROW MK5 Jetta WD for LED tail light if that even existed, can any of you Euro friends check your WD for plugs T4a & T4b pin location/ functions. NAR WD for MK5 Jetta tail lights connector plug T4a & T4b ROW WD for MK5 Jetta tail lights incandescent plug T4a & T4b
  19. MVB

    Looking for WD for tail lights for MK5 Jetta ROW

    Trying to compare how the NAR was wired compared to the ROW and if the ROW had one WD to cover both Incandescent & Led tail lights. The "incandescent" WD in german I have found and the plug and pins are as follows. ROW Jetta "incandescent" WD Plug T4a for Left side.......pin1 turn signal...
  20. MVB

    Can you disable the "press clutch to start" funtion, 2014 A4

    My NAR MK2 '87 GTI does not have a push to start clutch switch.
Top