Search results

  1. W

    Resolved 2013 Q7 - Suspension security access fail.

    Found the car had lowering links installed. Replaced the level sensor arms with stock parts and login/adaption completed without a problem.
  2. W

    Resolved 2013 Q7 - Suspension security access fail.

    Ya, like I said in the initial post. It accepts the login for basic settings, but not 31564 for adaption.
  3. W

    Resolved 2013 Q7 - Suspension security access fail.

    yes, it says 31564 to enable adaptation.
  4. W

    Resolved 2013 Q7 - Suspension security access fail.

    Car comes from another fault who replaced level control module, and pump, but could not calibrate. I found broken wire to right rear shock and repaired. Login for basic settings is accepted, but not 31564 for adaption. Only fault is 01437 - Control Position not Learned 005 - No or...
  5. W

    Resolved 2013 A8 Level calibration - Set reference level fail.

    Figured it out. Both rear pressure retention valves on the rear shocks were holding too much pressure and taking too long to lower. Removed them, ultrasonic bath in PBlaster and force some air through both ways... Calibrated properly and quickly.
  6. W

    Resolved 2013 A8 Level calibration - Set reference level fail.

    Yup. Every time. With a programming 200A charger on. Followed all prerequisites fearfully. 100% level fresh poured floor in my shop. Is there any way to figure out the actual cause of failure in measuring data?
  7. W

    Resolved 2013 A8 Level calibration - Set reference level fail.

    Anyone at Ross-tech have any suggestions?
  8. W

    Resolved 2013 A8 Level calibration - Set reference level fail.

    Tried with and without parking brake. Straight off the lift. After driving forward and back. Hood open or closed. Battery maintainer at 12.5/13/13.5/14/14.4v. With and without weight in the car.
  9. W

    Resolved 2013 A8 Level calibration - Set reference level fail.

    I've replaced a faulty level sensor on the right front (dealer part)- Following the procedure in UDS - re-adapt adaptive suspension exactly - as well as performing login between steps, waiting extra time in between steps, quickly changing steps immediately after finishing each, filling all bags...
  10. W

    HEX-NET license revoked, but support says it’s OK

    Up to date. cb: 0.4623 fw: 0.257 ds: 30000060 bl: 0.28 and the registered user is the person who i bought the interface from, who i am still in contact with. plugged in it shows slow flashing green, solid orange, solid green. I have tried holding the button for 60 seconds to clear the SD, but...
  11. W

    HEX-NET license revoked, but support says it’s OK

    I purchased a HEX-NET interface second hand (I also have a few interfaces that I purchased direct from Ross-tech). Today I go to use it like every other day and this comes up. Tried on 2 different PCs, updated software and firmware. When I use another interface it comes up OK. Please help. I...
  12. W

    Another MK60EC1 coding request

    Thanks to Iprot in dk for this coding that works. 114B400C492300FD880B02E8921A00413400
  13. W

    Another MK60EC1 coding request

    The original I only have the photo. I checked the coding vs the image many times, including plugging back in the original unit and testing coding again (with copy/paste). The BC unit takes longer coding than AD unit. I’m guessing they are incompatible, but I was hoping to get the coding and omit...
  14. W

    Another MK60EC1 coding request

    Copy/paste from original module did not with because coding is incorrect length. Removing the last 00 as I've used before also failed. Thursday,16,June,2022,16:20:19:35376 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x64 VCDS Version: 20.4.2.0 HEX-NET CB: 0.4613.4 Data...
  15. W

    Another MK60EC1 coding request

    3VWPZ7AJ7BM613041 old coding with 1K0 907 379 BC 114B400C492300FD880b02E8921A0041B70000 new(use) modules is 1K0 907 379 AD Failed with coding 114B400C492300FD880b02E8921A0041B700 Please help!
  16. W

    Coding to disable TPMS in Audi A8 D4

    This is what worked for me today on 2017 S8. Change cluster coding to remove TPMS. Information Electronics to Remove TPMS menu. Pull fuse SF4 in rear (fuse box F in trunk on back side of rear seat. 5amp, brown fuse holder on the right, 4th one down), then disconnect battery for 30 seconds. I...
  17. W

    MK60EC1 Coding - 2014 Passat

    I accidentally turned the key on with the cluster out and it lost ABS coding before I scanned the car. I know you like to have a full auto scan, but I only have the log with ABS faults and the vin - car is with customer. Returning tonight for the coding if you can help me. 1VWAT7A36FC013224...
  18. W

    CC - rear RPM sensors incorrect signal

    Car came in with a new LF abs sensor and what appears to be original RR sensor. When sensors are unplugged, faults change to open circuit faults. Measuring blocks 001 show wheel speed OK in front, but nothing in rear. I've tried changing CAN gateway coding to add TPMS 2, and I've tried changing...
Back
Top