Recent content by Keithuk

  1. Keithuk

    IE11 won't show this forum now RC4 problem

    Hi guys I've uses IE11 for many years for surfing and this forum. I click on the forum yesterday it shows a massage. RC4 cipher is no longer supported in Internet Explorer 11 or Microsoft Edge I've check the RC4 settings in Internet Options and they are ok. I've Googled this problem and on...
  2. Keithuk

    Http to https security

    Hi guys. I use a lot of forums over the past few weeks these forums have changed to https. I use IE11 for my main browser and Firefox as a backup. When I open these forums a message pops up at the bottom saying Only secure content is displayed which I ignore as the forum shows everything and...
  3. Keithuk

    2007 Passat 1.9 TDI won't go up a hill wiithout Limp Mode

    2007 Passat 1.9 TDI won't go up a hill only wiithout Limp Mode Hi Guys/gals. I have a friend who lives local with this problem with her 2007 Passat 1.9 TDI-PD BXE. It only goes up a hill the Malfunction Indicator Lamp (MIL)(K83) comes on. If the car stops and the turn the ignition off. Start...
  4. Keithuk

    How does VCDS find the engine code in log file?

    Hi guys/gals. How does VCDS find the engine code in log file, from the ecu? When I scan my Golf GTD it shows: Address 01: Engine (CBB) Labels: 03L-906-022-CBA.clb I know its abbreviated from CBBB. It shows CBB on the timing belt cover again why do VW abbreviated it? Older vehicle scans all...
  5. Keithuk

    Ross-Tech Wiki

    Hi guys/gals. There are a lot of codes on Ross-Tech Wiki. e.g. That says: Possible Solutions Check Fuse(s) Check Wiring and/or Connector(s) from/to Exhaust Gas Recirculation (EGR) Valve (N18) Check/Replace Exhaust Gas...
  6. Keithuk

    LED strip light indictor in door mirror

    It isn't only a Mk6 Golf problem as the same type of light is fitted to other models. I've had an error code for a few months. The indictor strip light works on both mirrors so I haven't really bothered about it. Last week I noticed the light in the drivers door the one with the fault code...
  7. Keithuk

    Adapt Automatic Run & Pinch Protection (see Special Notes).

    This is not a forum feedback but Ross-Tech Wiki. You can move this thread if you want too? I've just done a scan on a 2008 Skoda Octavia 1.9 TDI and its come back with error codes which I can post the full AutoScan if needed. This is the one that needs more info...
  8. Keithuk

    Function not supported by the gateway

    Hi guys. I know I added my comments to a couple of other threads on the same subject, with no real solution, so I may as well make my own thread. Help, no response from (CAN) Gateway 2016 Skoda Fabia & Citygo not DTC scan I installed the new VCDS Release 16.8.0 the other day and I've just...
  9. Keithuk

    Keith's AutoScan.txt Questions

    Chassis Type: AU (5Q0) Scan: 01 02 03 05 08 09 10 13 15 16 17 19 22 2B 42 44 47 52 55 5F A9 Your using AU chassis Type: AutoScan.txt shows: AU,VW Golf/Jetta VII NAR (2015 >),00 when your in Sweden!!! Scan: 01 02 03 05 08 09 10 13 15 16 17 19 22 2B 42 44 47 52 55 5F A9 I've always used 1K for...
  10. Keithuk

    Adjustment of rotational rate & lateral/longit acc sensor G200/G202/G251

    I have a 2008 Passat 2.0 TDI with a few faults. I tried to get basic setting for G200 sensor. It only shows Adjustment of rotational rate & lateral/longit acc sensor (G200/G202/G251) - 061 error not...
  11. Keithuk

    VCDS Auto-Scan stops at #17

    I install all new updates when they come out. Last month after VCDS Release 14.10.1 I did a scan just to try it out and it stopped responding so I had to End Task it after a couple of minutes. It only scanned down to Address 17: Instruments (J285) Labels: 5K0-920-xxx-17.clb then stopped. I...
  12. Keithuk

    008585/ P2189 2007 Q7

    Its strange you have these two I have. 008583 - Bank 1; System too Lean at Idle P2187 - 004 - - MIL ON VAG Error Code: 008585 EOBD II Error Code: P2189 Fault Location: System too Lean at Idle, Bank 2 Possible Cause: Malfunction...
  13. Keithuk

    VCDS Beta 14.9.0 out of date

    Hi guys. I've just plugged it in to do my normal scan VCDS Release 14.10.0 after it finished I thought I would give the VCDS Beta 14.9.0 ago. All buttons were disabled and a message at the top said it out of date. I went online the and...
  14. Keithuk

    00200 Create the page

    Hi guys. On Ross-Tech Wiki e.g. 00200 it says Create the page "00200" on this wiki! it says: It would be nice to create this code but...
  15. Keithuk

    Ross-Tech Wiki Log In!!!

    Hi guys. I see on Ross-Tech Wiki there is a log in screen. I've tried this forums log in but there in no username or email. I see no link to register what's the purpose of the login?