I dont think... All A6 C7.5 have keyless start, so there are already 2 antenas - one in center console ane one in back door. So All keys from A6 C7.5 are identical (frequency depend on region). (i checked in PartsLink with VIN code - i had A6 with keyless and now this present A6 withhou keyless...
Hello, my keys should be Kessy, because i dont put key directly to board. I compared original parts with car with kessy and it have the same key 8K0 959 754
Now i uploaded in VCP parametr files A6_start_auth_4H0907064Fx.zdc with kessy to 05 (not 46 - it was error) and it was ok but now there is...
i made retrofit for Keyless go:
2x Antena 8K0907247
1x 5th door switch 4G0959831B 5PR
1x 5th door unit 3AA962243D + antena + cable
4x Door handle sensor 4G8927753B (ALIExpress) + cables
1x 46 Comfort unit 4H0907064GP - fitted in AUDI service with key programming
After swap 46 Comfort...
I think, that i have to swap 46 Comfort unit - i see lot of scans, and no xxxxxN comfort unit have keyless.
I let audi swap it, so i will see if it will be ok. I already have all stuff for it but thank you ...
I let here know my conclusion...
Can you tell me if your original 46 unit was working with kessy or you have to swap it ?
I have: Part No SW: 4H0 907 064 FN HW: 4H0 907 064 EN
I still have no connected sensors and antena, but i first tried, if my 46 Comfort unit is ok for kessy.
I flashed it twice...
is there any way to change speed of activation Matrix High Beam when you have automatic light switched on?
In City there is activation speed aprox 60-70km/hod, it should be nice if it was lower.
Dana/Uwe I can send you also full scan and adaptation channels of my Q7 Etron, there is very...
is there any way to reprogram 6D: Trunk Elect for closing trunk by push button on remote control and push button in drivers door ? I know that hold will work, but it is more comfortable only click. I have successfuly made on A6 C7 but on Q7 without success.
I found on internet only MKDS...
I swapped seatbelts in all car Audi A4 B8 2012+ and all seems to be ok, but from driver and passangers seatbelts i got errors (there is different ressistance of new front seatbelts than in old one). Both should be from facelift.
Is there any way to tell airbags unit, that this 3,1-3,2 ohms...
Hello, does somebody tested using prefacelift 08- Auto HVAC (4 zone clima) in facelift with working clima ?
They dit in Audi, but cannot get cooling working.
Originaly i had:
4G0820043CC (no heating, no ventilation) - facelift - coding 34020978210000
I tried to use there
tried someone this ?
Upgrade in Audi A6 Facelift from Xenon (hope with AFS) to Full LED (not Matrix).
It have the same wiring ? (i do not have new elsa)
I have also high beam camera, and my friend have a car (RS6), where are Full Led original fitted. So it is possible download adaptation...
i retrofited in Audi A4 Avant 2013+ B8 where is ACC and Lane Assist - Side Assist and Trailer Hitch.
Made someone coding on similar car ? In Acc is original coding here.
In VCDS is no label for ACC and this write error:
Chassis Type: 8K-AU48 (8R0)
Scan: 01 02 03 05 08 09 13...
I have car prefacelift A3 8V 2015 with missing (Stolen) LED headlights.
Did someone tried upgrade to Facelift LED (not Matrix) ?
What is except front bumper and Headlighs with units needed ?
I have not VCDS scan yet :-/
Audi A6 2012 MMI 3GP with sim
and there does not work internet via SIM (T-mobile CZ) - newest FW 1001 and maps 6.25.3 (i have there also right APN for my provider)
Now i got from friend newer A6 2013 with MMI 3GP and older FW (aprox 6xx) - and internet does not work too. I tried...
I made retrofit of rear PDC on Golf MK7 Variant and used there unit what can operate with 8K sensor.
Now i have 2 problems:
- it write error that there is no front sensors + speaker
- not show PDC OPS display on headunit
Is there any way to get working only 4 rear sensors with this 8K PDC...