Recent content by KraftwerkTurbo

My KESSY module failed due to corrosion. I bought a good used one with matching numbers. Before swapping the modules: do I need to adapt the new module to the car? If so, link to the procedure? Scan from old module: Address 05: Acc/Start Auth. Labels: 3D0-909-13x-05.lbl Part No...

Had to buy new computer. Only windows 10 and only USB-C. I bought USB-old to USB-C adapter. Will that (and Windows 10) work with my HEX-USB+CAN cable?

Trying to help a friend with his 2001 Jetta. Car cranks, starts, dies after 2 sec. First though immo kicks in (and could well be). Plugging VAGcom in, does not connect to ANY module. Plugged another ECU I had on hand, same behavior. Took the ECU out and plugged into my bench setup...

Car (2006 B6 Passat 2.0T FWD) was (almost) fine. Then in short period: gas filler flap solenoid not opening, heater fan stopped working, electrical break stopped working, instrument cluster no speedometer and gas gauge goes nuts. Not sure about ABS/traction control (if that also occurred or was...

Is my Hex+Can (HEX-USB+CAN) working for 2014 Panamera Turbo S?

What block should I use to check timing on BPY (2006 Passat 2.0T) engine? What values/range is correct for those blocks? I am used to 090-093 for the 1.8T and 2.7T engines, but have not used VAGcom for timing on 2.0T FSI engines yet.

I have swapped the ECU, need to change the ECU softcoding. Getting error "outside of range". need to softcode to 0016711. Any idea why it is not 'taking'? Is a login required to softcode the ECU?

Can I delete the "old" "older" "oldest" directories under the VCDS directory? Just keep the "Labels" folder?

Is the mileage stored in other locations than just the cluster? I am reading, but owner says should be 11,000 miles. Is he maybe reading the 'trip counter' mileage? Currently not at car to verify. Thursday,29,November,2018,14:53:19:03761 VCDS -- Windows Based VAG/VAS Emulator Running on...

A few miles ago I found these codes: 000564 - Boost Pressure Regulation P0234 - 001 - Limit Exceeded (Overboost Condition) - MIL ON 000257 - Mass Air Flow Sensor (G70) P0101 - 008 - Implausible Signal - Intermittent Also tranny code: 18265 - Load Signal P1857 - 000 - Error Message from ECU...

Don't have the car here so can't quickly check. Does my Hex+CAN work with above car? How about my KII-USB?

Getting the code since we bought the car. All stock AFAIK. Is the code thrown because of some shoddy work (change a module) of the previous owner? Which module is incorrectly coded? Any suggestions how to troubleshoot? Code comes right back after erasing. Address 19: CAN Gateway...

I tried to download software for my Hex-USB cable, but all websites are not connecting. Is server down.

Still fighting code 17748 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28) P1340 - 35-00 - Incor. Correlation after engine build. 2001 Audi TT225 AMU block. New bearings, rods, rings, seals, oil pump. Rebuild AEB head. New VVT cam chain tensioner (not connected). AMU valve...

Suggestions what might be causing the 2 codes? Where to start with troubleshooing? 40k miles. Wednesday,10,January,2018,15:23:56:03761 VCDS Version: Release 17.8.1 (x64) Running on Windows 7 x64 www.Ross-Tech.com Address 01: Engine Labels: 06H-907-115-CDN.clb Control...