Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Retrofitting bi-xenon Amarok 2013

  1. #1
    Verified VCDS User
    Join Date
    Jul 2017
    Location
    Sweden
    Posts
    13
    Post Thanks / Like

    Retrofitting bi-xenon Amarok 2013

    Hi
    I have installed Oem xenon in my Rok after some instructions I have found from Eballs28 on this forum.

    This is how I want the lights to operate:
    Led Drl have to be on at the same time as the rear parking lights (Swedish rules)
    When it's getting dark outside the Led Drl should be dimming when the headlight comes on.

    My -13 have all options available at the time inc Nav Rns510
    And my BCM module have the number 7H0 937 090.

    With no coding done everything worked as before with the halogen lights except for the Led Drl.

    I have been installing new wires from the BCM T73b/5 and 6 to each headlight connector 10.

    Now to the coding I will need some help with that as the coding instructions from Eballs28 doesn't seem to work for my car.

    This is what worked for Eballs28

    Central electric module 9

    Byte11, bit0 needs to be a 1
    Byte12, bit0 needs to be a 1
    Byte22, bit4 needs to be a 1
    Byte18, needs to have a hex value of 67

    One problem for me is that I cant see all the "byte" checkboxes In my vcds

    When I did the complete Eballs28 coding nothing worked and the xenon was strobing/flashing.

    But when I did Byte22 coding alone and nothing else the Led Drl started working
    But it's no parking light in the rear.

    If I go to byte12 and do bit 0 to 1 the Led Drl comes off and the rear parking lights starts working instead.


    When I cover the light sensor the LED Drl comes off and the Xenon headlight starts working instead . When the Led is suppose to be dimming.

    My Pc crashed today and after a reinstall of windows I can't get explorer to access the internet so I had to take a picture of the coding with my phone and post this from my iPad I hope that's ok

    Coding pic.
    http://forumbilder.se/G8VVP/img-3971
    http://forumbilder.se/G8VVP/img-3972

  2. #2
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    17,980
    Post Thanks / Like
    Blog Entries
    1
    Please see: How to Get Verified.

    -Uwe-
    The engineering problems are likely insurmountable. It would be like proposing to land a rocket booster section on a barge floating in the middle of the ocean.

  3. Likes Dana liked this post
  4. #3
    New User
    Join Date
    Jan 2018
    Location
    Ecuador
    Posts
    2
    Post Thanks / Like
    Hi


    I bought the bi-xenon DRLs for my Amarok'16 2HBB3A TDI 2.0.

    I went to my local dealer to install them but we are having some issues.


    First of all I follow all the instructions I could find about the installation, this means I connected the t73b pin 5 to the left light and the t73b pin 6 to the right light, both on pin 10.


    n 5 Mass

    n 10 BCM

    n 6 Low

    n 8 high

    n 9 Turn

    n 4 Position

    Also the configuration on my Comfort Module 09 is:


    Byte 11 bit 0 to 1 to activate high beam shutter
    Byte 18 changed to 67 or 65 if using LED number plate lights
    Byte 22 bit 4 to 1 to enable LED module for DRL and Parking Lights.

    Doing this, when the motor is running the led DRL's start flashing as strobe lights, the DRL doesn't work (daylight), and when I turn on the middle lights the LED DRL DIMs which it should do but still flashes all the time. I also have the light bulb fault on my dashboard.

    Could you please help me, do you have any guide, wiring diagram and instructions including codification, on what I should do in order for this to work properly?, what can I do to fix this.

  5. #4
    Verified VCDS User iichel's Avatar
    Join Date
    Aug 2016
    Location
    Switzerland
    Posts
    1,013
    Post Thanks / Like
    please post a full autoscan. i'll have a look...
    Last edited by Uwe; 01-07-2018 at 05:37 PM. Reason: Added Link

  6. Likes Uwe liked this post
  7. #5
    New User
    Join Date
    Jan 2018
    Location
    Ecuador
    Posts
    2
    Post Thanks / Like
    Hi iichel, sorry for the late response, I had an accident earlier this year and still haven't been able to fit the bi-xenon headlights on my AMAROK, once the car is ready I will continue with the retrofit as nothing has changed so far.
    Thanks in advance for your help.

  8. Likes iichel liked this post
  9. #6
    New User
    Join Date
    Mar 2018
    Location
    Romania
    Posts
    8
    Post Thanks / Like
    Code:
    Tuesday,29,May,2018,12:17:03:11999
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86
    VCDS Version: 18.2.1.2
    Data version: 20180518 DS287.1
    www.Ross-Tech.com
    
    
    VIN: WV1ZZZ2HZB8062680   License Plate: XXX
    Mileage: 173470km-107789mi   Repair Order: 1234
    
    
    
    --------------------------------------------------------------------------------
    --------------------------------------------------------------------------------
    
    
    Chassis Type: 2H-VN81 (6N0)
    Scan: 01 03 04 08 09 15 17 19 25 32
    
    VIN: WV1ZZZ2HZB8062680   Mileage: 173470km-107789miles
    
    01-Engine -- Status: Malfunction 0010
    03-ABS Brakes -- Status: Malfunction 0010
    04-Steering Angle -- Status: OK 0000
    08-Auto HVAC -- Status: Malfunction 0010
    09-Cent. Elect. -- Status: Malfunction 0010
    15-Airbags -- Status: Malfunction 0010
    17-Instruments -- Status: OK 0000
    19-CAN Gateway -- Status: Malfunction 0010
    25-Immobilizer -- Status: OK 0000
    32-Differential Locks -- Status: Malfunction 0010
     
    -------------------------------------------------------------------------------
    Address 01: Engine (J623-CDCA)       Labels:. 03L-906-022-CAA.clb
       Part No SW: 03L 906 019 FC    HW: 03L 907 309 K
       Component: R4 2.0l BTD   H40 9978  
       Revision: 26H40---    Serial number: 00000000000000
       Coding: 01194012232600080000
       Shop #: WSC 28315 001 1048576
       ASAM Dataset: EV_ECM20BTD01103L906019FC 004006
       ROD: EV_ECM20BTD01103L906019FC_004.rod
       VCID: 71E9EE97A087C5CCD8-8024
    
    8 Faults Found:
    4332 - Check Coding of ECUs on Powertrain Data Bus 
              P1647 00 [036] - -
              [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
              Intermittent - Not Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 2
                        Fault Frequency: 10
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 18 C
                        Intake air temperature: 21 C
                        Ambient air pressure: 980 mbar
                        Voltage terminal 30: 11.800 V
                        Unlearning counter according OBD: 40
                        ACC target acceleration: 0.000 m/s
                        ACC control module received status-Bits 0-7: 6
                        Status of ACC/CCS acceleration interface-Bits 0-7: 0
                        Acceleration: 0.000 m/s
                        Engine status: COENG_READY
                        Engine status-Test_Program_Co Eng st COMPU VERB UBYTE: 1
    
    4481 - Cruise Control Switch (E45) 
              P0568 00 [044] - Implausible Signal
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 2
                        Fault Frequency: 4
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 26 C
                        Intake air temperature: 20 C
                        Ambient air pressure: 970 mbar
                        Voltage terminal 30: 13.200 V
                        Unlearning counter according OBD: 40
                        Cruise Control System (CCS): switch position-Bits 0-7: 129
                        Cruise Control System (CCS): status-Bits 0-7: 232
                        Cruise control switch-off: irreversible-Bits 0-7: 255
                        Cruise control switch-off: reversible-Bits 0-7: 255
                        Cruise Control System: specified speed: 0.00 km/h
                        Engine control module reset status-Bits 0-7: 0
                        Engine control module reset status-Bits 0-7: 2
                        Cruise control switch-off: irreversible w. brake intervention-Bits 0-7: 0
    
    4482 - Function Restriction due to Implausible Message(s) 
              U1112 00 [044] - -
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 2
                        Fault Frequency: 15
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 26 C
                        Intake air temperature: 20 C
                        Ambient air pressure: 970 mbar
                        Voltage terminal 30: 13.200 V
                        Unlearning counter according OBD: 40
                        Cruise Control System (CCS): switch position-Bits 0-7: 193
                        Cruise Control System (CCS): status-Bits 0-7: 232
                        Cruise control switch-off: irreversible-Bits 0-7: 255
                        Cruise control switch-off: reversible-Bits 0-7: 255
                        Cruise Control System: specified speed: 0.00 km/h
                        Engine control module reset status-Bits 0-7: 0
                        Engine control module reset status-Bits 0-7: 2
                        Cruise control switch-off: irreversible w. brake intervention-Bits 0-7: 0
    
    4483 - Function Restriction due to Faults in Other Modules 
              U1113 00 [044] - -
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 8
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 22 C
                        Intake air temperature: 23 C
                        Ambient air pressure: 970 mbar
                        Voltage terminal 30: 14.240 V
                        Unlearning counter according OBD: 40
                        Cruise Control System (CCS): switch position-Bits 0-7: 193
                        Cruise Control System (CCS): status-Bits 0-7: 232
                        Cruise control switch-off: irreversible-Bits 0-7: 255
                        Cruise control switch-off: reversible-Bits 0-7: 255
                        Cruise Control System: specified speed: 0.00 km/h
                        Engine control module reset status-Bits 0-7: 0
                        Engine control module reset status-Bits 0-7: 2
                        Cruise control switch-off: irreversible w. brake intervention-Bits 0-7: 0
    
    4708 - No Communications with HVAC Control Module (J301) 
              U0164 00 [036] - -
              Intermittent - Not Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 5
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 21 C
                        Intake air temperature: 22 C
                        Ambient air pressure: 980 mbar
                        Voltage terminal 30: 12.600 V
                        Unlearning counter according OBD: 40
                        Limitation: accelerator pedal: 0.0 Nm
                        CAN status - engine control module-Bits 0-7: 0
                        Cruise Control System (CCS): status-Bits 0-7: 200
                        CAN status - transmission control module-Bits 0-7: 0
                        CAN status - brake control module 1-Bits 0-7: 0
                        CAN status - brake control module 2-Bits 0-7: 0
                        selected gear-Bits 0-7: 0
    
    4717 - Body Control Module (Central Electric) 
              U0140 00 [036] - No Communications
              Intermittent - Not Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 5
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 21 C
                        Intake air temperature: 22 C
                        Ambient air pressure: 980 mbar
                        Voltage terminal 30: 12.600 V
                        Unlearning counter according OBD: 40
                        Limitation: accelerator pedal: 0.0 Nm
                        CAN status - engine control module-Bits 0-7: 0
                        Cruise Control System (CCS): status-Bits 0-7: 232
                        CAN status - transmission control module-Bits 0-7: 0
                        CAN status - brake control module 1-Bits 0-7: 0
                        CAN status - brake control module 2-Bits 0-7: 0
                        selected gear-Bits 0-7: 0
    
    4719 - No Communication with Diagnostic Gateway 
              U0146 00 [036] - -
              Intermittent - Not Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 4
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: 21 C
                        Intake air temperature: 22 C
                        Ambient air pressure: 980 mbar
                        Voltage terminal 30: 12.600 V
                        Unlearning counter according OBD: 40
                        Limitation: accelerator pedal: 0.0 Nm
                        CAN status - engine control module-Bits 0-7: 0
                        Cruise Control System (CCS): status-Bits 0-7: 201
                        CAN status - transmission control module-Bits 0-7: 0
                        CAN status - brake control module 1-Bits 0-7: 0
                        CAN status - brake control module 2-Bits 0-7: 0
                        selected gear-Bits 0-7: 0
    
    4629 - ECM Power Relay Load Circuit 
              P068A 00 [040] - Opens Too Early
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 2
                        Fault Frequency: 1
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Engine speed: 0.00 /min
                        Normed load value: 0.0 %
                        Vehicle speed: 0 km/h
                        Coolant temperature: -40 C
                        Intake air temperature: -40 C
                        Ambient air pressure: 0 mbar
                        Voltage terminal 30: 0.000 V
                        Unlearning counter according OBD: 40
                        Accelerator pedal travel: 0.00 %
                        Starter control: Interlock- or P/N-signal-Bits 0-7: 0
                        Engine status: COENG_STANDBY
                        Engine status-Test_Program_Co Eng st COMPU VERB UBYTE: 0
    
    Readiness: 1010 0000
    
    -------------------------------------------------------------------------------
    Address 03: ABS Brakes (-----)       Labels:. 2H0-907-37x-ESP.clb
       Part No SW: 2H0 907 379 G    HW: 2H0 907 379 D
       Component: ESP MK25A XT  H44 0106  
       Revision: 00H44001    
       Coding: C07324B69A9A039724A859AB6F5010
       Shop #: WSC 07456 790 49164
       VCID: 346727839715B0E4F3-8060
    
    3 Faults Found:
    01317 - Control Module in Instrument Cluster (J285) 
                000 -  -  - Intermittent
                 Freeze Frame:
                        Fault Status: 00100000
                        Fault Priority: 3
                        Fault Frequency: 1
                        Reset counter: 0
                        Time Indication: 0
    
                 Freeze Frame:
                        Count: 32768
                        Count: 4097
                        Count: 8280
                        Count: 514
    
    03095 - Diagnostic interface for databus (J533) implausible messa.: 
                000 -  -  - Intermittent
                 Freeze Frame:
                        Fault Status: 00100000
                        Fault Priority: 6
                        Fault Frequency: 1
                        Reset counter: 0
                        Time Indication: 0
    
                 Freeze Frame:
                        Count: 32768
                        Count: 4097
                        Count: 8257
                        Count: 514
    
    01299 - Diagnostic Interface for Data Bus (J533) 
                004 - No Signal/Communication - Intermittent
                 Freeze Frame:
                        Fault Status: 00100100
                        Fault Priority: 2
                        Fault Frequency: 1
                        Reset counter: 0
                        Time Indication: 0
    
                 Freeze Frame:
                        Count: 32832
                        Count: 4097
                        Count: 8233
                        Count: 514
    
    
    -------------------------------------------------------------------------------
    Address 08: Auto HVAC
    Cannot be reached
    
    -------------------------------------------------------------------------------
    Address 09: Cent. Elect. (J519)       Labels:. 7H0-937-08x-09.clb
       Part No SW: 7H0 937 090 D    HW: 7H0 937 090 
       Component: BCM PQ25 Max4 H78 0725  
       Revision: B9078001    Serial number: 9000 219150127
       Coding: 350006380C211000003008312ECB96DD0F80664E60003040300000030003
       Shop #: WSC 12345 123 12345
       VCID: 2F6D28EF7E33933C8E-807A
    
       Subsystem 1 - Part No SW: 6R0 959 801 M    HW: 6R0 959 801 M  Labels: 6R0-959-801.CLB
       Component: J386__TSG_FT  002 3321 
       Serial number: --------------------
       Coding: 100000
    
       Subsystem 2 - Part No SW: 6R0 959 802 P    HW: 6R0 959 802 P  Labels: 6R0-959-802.CLB
       Component: J387__TSG_BT  002 3321 
       Serial number: --------------------
       Coding: 100000
    
       Subsystem 3 - Part No: 1K8 951 605 B
       Component: LIN BACKUP HO  H11 9005 
       Coding: 000000
    
       Subsystem 4 - Part No SW: 6R0 959 811 D    HW: 6R0 959 811 D
       Component: J388__TSG_HL  002 3321 
       Serial number: --------------------
       Coding: 100000
    
       Subsystem 5 - Part No SW: 6R0 959 812 D    HW: 6R0 959 812 D
       Component: J389__TSG_HR  002 3321 
       Serial number: --------------------
       Coding: 100000
    
    2 Faults Found:
    01044 - Control Module Incorrectly Coded 
                000 -  - 
                 Freeze Frame:
                        Fault Status: 01100000
                        Fault Priority: 2
                        Fault Frequency: 1
                        Reset counter: 255
                        Time Indication: 0
    
    01504 - Bulb for License-Plate Light (X) 
                010 - Open or Short to Plus
                 Freeze Frame:
                        Fault Status: 01101010
                        Fault Priority: 3
                        Fault Frequency: 1
                        Reset counter: 0
                        Time Indication: 0
    
    
    -------------------------------------------------------------------------------
    Address 15: Airbags (J234)       Labels:| 5K0-959-655.clb
       Part No SW: 2H0 959 655 B    HW: 2H0 959 655 B
       Component: VW10Airbag00B H06 0013  
       Revision: --------    Serial number: 003HN002N3WH
       Coding: 000000000000000000000000000000003042
       Shop #: WSC 07446 790 50316
       ASAM Dataset: EV_AirbaVW10BPAVN750 A01026
       ROD: EV_AirbaVW10BPAVN750_VW12.rod
       VCID: 3365249F9A1BB7DCEA-8066
    
       Crash sensor for side airbag: driver side: 
       Serial number: 3495RRB40590BTBE4GV5
    
       Crash sensor for side airbag: front passenger side: 
       Serial number: 3505RRB40590BTBE7OT6
    
       Crash sensor for front airbag: driver side: 
       Serial number: 3555YRB405F060GK4GPT
    
       Crash sensor for front airbag: front passenger side: 
       Serial number: 3565YRB405H060GKP98T
    
    2 Faults Found:
    9437211 - Igniter for Driver's Airbag 
              B1000 1B [137] - Resistance Too High
              MIL ON - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 2
                        Fault Frequency: 1
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
    12666368 - Databus 
              U1122 00 [008] - Implausible Message
              [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 3
                        Reset counter: 40
    
    
    -------------------------------------------------------------------------------
    Address 17: Instruments (J285)       Labels:| 5K0-920-xxx-17.clb-SRI1
       Part No SW: 2H0 920 863 A    HW: 2H0 920 863 A
       Component: KOMBI         H05 0304  
       Serial number: 00000000000000
       Coding: 150A00
       Shop #: WSC 07456 790 50316
       ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04086
       ROD: EV_Kombi_UDS_VDD_RM09_004_VW32.rod
       VCID: 275DC0CF5EC3CB7C46-8072
    
    2 Faults Found:
    12664832 - Function Restricted due to Missing Message(s) 
              U1111 00 [009] - -
              [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
              Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 1
                        Reset counter: 0
    
    13635840 - Supply voltage 
              U1011 00 [008] - Voltage too Low
              [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 6
                        Fault Frequency: 1
                        Reset counter: 40
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
    
    -------------------------------------------------------------------------------
    Address 19: CAN Gateway (J533)       Labels:. 6N0-909-901-6R.clb
       Part No SW: 6N0 909 901     HW: 7H0 937 090 
       Component: GW-K-CAN TP20 H78 0725  
       Revision: B9078001    
       Coding: 742200
       Shop #: WSC 12345 123 12345
       VCID: 70EFEB93A38DCCC4D7-8024
    
    2 Faults Found:
    01336 - Company Data Bus for Comfort System 
                004 - No Signal/Communication - Intermittent
                 Freeze Frame:
                        Fault Status: 00100100
                        Fault Priority: 1
                        Fault Frequency: 21
                        Reset counter: 40
                        Time Indication: 0
    
    00381 - Databus Instrument Cluster 
                004 - No Signal/Communication
                 Freeze Frame:
                        Fault Status: 01100100
                        Fault Priority: 1
                        Fault Frequency: 254
                        Reset counter: 0
                        Time Indication: 0
    
    
    -------------------------------------------------------------------------------
    Address 25: Immobilizer (J334)       Labels:| 5K0-920-xxx-25.clb
       Part No SW: 5K0 953 234     HW: 5K0 953 234 
       Component: IMMO          H05 0304  
       Serial number:               
       Coding: 000000
       Shop #: WSC 00000 000 00000
       ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03008
       ROD: EV_Immo_UDS_VDD_RM09.rod
       VCID: 6ADBF9FB8D51361499-803E
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 32: Differential Locks (J647)       Labels:* 2H0-927-771.clb
       Part No SW: 2H0 927 771     HW: 2H0 927 771 
       Component: Quersperre    H04 0014  
       Revision: 11001001    Serial number: 4DG 18.11.10 00
       Coding: 000001
       Shop #: WSC 00000 000 00000
       ASAM Dataset: EV_QuersUDSAAMVN817 A01005
       ROD: EV_QuersUDSAAMVN817.rod
       VCID: 6BD5FCFF82AB2F1CE2-803E
    
    1 Fault Found:
    12666368 - Function Restricted due to Missing Message(s) 
              U1111 00 [008] - -
              [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
              Intermittent - Confirmed - Tested Since Memory Clear
                 Freeze Frame:
                        Fault Status: 00000001
                        Fault Priority: 1
                        Fault Frequency: 4
                        Reset counter: 40
                        Mileage: 0 km
                        Date: 2000.00.00
                        Time: 00:00:00
    
                        Vehicle speed: 0 km/h
                        Engine speed: 0.00 /min
                        Voltage terminal 30: 12.4 V
                        Voltage at sensor: 1.1 V
                        Actuator: coil current: 0.0 A
    
    
    End-------------------------(Elapsed Time: 03:54)--------------------------
    Last edited by Uwe; 05-29-2018 at 09:05 AM. Reason: CODE tags

  10. #7
    New User
    Join Date
    Mar 2018
    Location
    Romania
    Posts
    8
    Post Thanks / Like
    I have the auto scan on my car
    i have the daylight running but when it goes to turn on the lights the drl stops working

  11. #8
    New User
    Join Date
    Mar 2018
    Location
    Romania
    Posts
    8
    Post Thanks / Like
    what is wrong

  12. #9
    New User
    Join Date
    Mar 2018
    Location
    Romania
    Posts
    8
    Post Thanks / Like
    @iichel if you can help me, i am in the service with the car

  13. #10
    Verified VCDS User PetrolDave's Avatar
    Join Date
    Dec 2014
    Location
    South Molton, UK
    Posts
    1,001
    Post Thanks / Like
    Quote Originally Posted by Aronclb View Post
    I have the auto scan on my car
    i have the daylight running but when it goes to turn on the lights the drl stops working
    Do you mean the DRLs turn off when the other lights turn on?

    If you do then that is normal behaviour - because when it's dark enough for the other lights to be on then there is no need for the DRLs to be on (as it's no longer Daylight!).

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •